goop on nozzle after prime blob
I get this a lot. How much depends on the filament, and probably temperature.
continuation of conversation here: https://discord.com/channels/582187371529764864/1246562369513984100/1302452251041726549
after an hour of printing most of the filament from the prime blob will have wiped off, though you can see the remains of it still. (see marked image)
The excess filament on the outside of the nozzle tends to cause messy first layers as that filament is slowly dragged off during the print....
_USER_END_PRINT_PARK Macro misbehaving
W have a macro that should reset extrusion factor and printspeed back to 100% and also clear the skew profile, like so:
```
[gcode_macro _USER_END_PRINT_PARK]
gcode:
M220 S100 ;set printspeed back to 100% in case I have tweaked it during printing...
IDEX Misses Z moves
I star to test dual material printing but I encouter one issue.
I tried to print this minion but when there is tool change that has little to no outter walls the printer doesn't move on Z to make the layer change. It's strange because at the lower layers of the minion it's working fine.
I checked the gcode from OrcaSlicer and the layer change is there. It seams like the post processor is removing it or the printers is skipping it for some reason....
TMC ‘extruder’ reports GSAT
Hello,
My printer keeps throwing this error at 95% or so of a 24 hour long print. I attached a picture below to show. Any idea what’s causing this? I checked my wiring and it’s all fine looking. Also, the print started looking bad before this error. And ideas?...
How to avoid Y collision in IDEX configuration?
I had
on V-Core 400
and works with VAOC calibration because during the VAOC procedure, both the toolheads moves away from Y motors.
If I manually move the Y axis with T0 in home position and T1 parked, T1 at +408 collides with the motor....
Solution:
If I manually move the Y axis with T0 in home position and T1 parked, T1 at +408 collides with the motor.Yeah.. Don't do that....
MCU shutdown: timer too close - after I start a print (quite a heavy file)
Hi, any ideas what is wrong with my printer? Once I have started a big print job, klipper shuts down with this error (photo below). I have done a couple of small prints with no problem, so I assume the gcode file is too heavy (which would be weird in my opinion)
Not understanding VAOC calibration
I found this video on the discord https://www.youtube.com/watch?v=_ooNQt7qPSs that goes through vaoc, but I feel it doesn't help my situation. I calibrate t0, change camera settings, make circles align with nozzle, then move onto t1 and do the same. I go back to t0, and it is "misaligned". I fix it then go back to t1, and it is misaligned. From what I understand from that video, switching should save the calibrated toolhead, but I don't know what I am doing wrong. The pics I added are t0 > t1 >...
Chonk Triple Z Beta testing. Need help
Here is a video of the Chonk carrying out z tilt. Im not sure if your 170mm limitation is causing this but the first touch of the rear only during z tilt does is grind. I am not see anything touch. The right side doesnt home in the same y distance compared to the left like my v-core. Just noting that. Also the printer is layer shifting pretty bad at the moment. Any insight on that would be greatly at. I thought it may be from the initial grind but it carries all the way through the print. I have my belt on the tighter end at the moment compared to my sloppy 500.
https://youtube.com/shorts/LUznoPSbQBA...
Update Manager doesn´t work
Now that my VCore4 system is fully installed, I wanted to start the update manager, but not much is happening. It idles a bit, CPU usage fluctuates a bit, but no data is actually transferred. After 5-10 minutes, the update hook is back and nothing happens. It also makes no difference whether it is WiFi or LAN. Moonraker conf. is apparently OK, at least it matches my Vorons. If you mean it´s a theme for the mainsail channel, feel free to move it.
Inconsistent first layer between prints with Beacon
I am currently struggling with first layer issues. I am currently only printing single layer 100 mm x 100 mm x 0.3 mm shapes to test this. My first print of a day or a work session starts looking decent and then the surface begins to have ripples indicating there is too much squish.
I remove the print and immediately reprint the same file (select reprint from within RatOS) and it prints without any of the rippling issues.
I have adjusted the microstepping for a motors to be 16 as was suggested by others here. ...
