Dom Dell Computer
RRCRat Rig Community [Unofficial]
•Created by Dom Dell Computer on 4/25/2025 in #fix-my-printer
Part cooling fan not turning on after resume
Idex printer here... when I get a filament runout pause. the PCF turns off, which is fine. Problem is it will not automatically set to the power setting it was at before when calling the resume macro, the printer resumes with the PCF off, my prints suffer if I forget to manually turn it on. How to can I configure RATOS to resume the PCF fan state?
Below is my F sensor code:
[filament_motion_sensor bowden_filament_clog_t1]
switch_pin: PG15
detection_length: 14
extruder: extruder1 # extruder for T0, extruder1 for T1
pause_on_runout: True
event_delay: 3.0
pause_delay: 0.5
runout_gcode:
M117 T1 Clog
_ON_BOWDEN_FILAMENT_SENSOR_CLOG TOOLHEAD=1
insert_gcode:
I dont have any hooks defined at the moment. TIA
2 replies
RRCRat Rig Community [Unofficial]
•Created by Dom Dell Computer on 11/24/2024 in #fix-my-print
Vcore 3.1 idex overhangs and support material

3 replies
RRCRat Rig Community [Unofficial]
•Created by Dom Dell Computer on 11/7/2024 in #fix-my-printer
Connecting Stealthmax via Stealthmax pcb v2
I am trying to get my SM to work with the printer and I ma getting odd behavior. It seems to use the same id as my t0, I thought I got around that by defining the path, now what happens is klipper never starts because it cant connect to t0 or the SM, or the thermistor on t0 reads a crazy high temp. Disabling the SM config and a hard reboot gets my back into klipper. WHat can I do here?
4 replies
RRCRat Rig Community [Unofficial]
•Created by Dom Dell Computer on 11/3/2024 in #fix-my-printer
Vcore 3.1 IDEX nozzle wipe
I designed an arm that has a wire brush built into it so I can potentially wipe my nozzle before tool changes. I am having trouble finding where I could tell the printer to "brush" the next tool to remove oozing and blobs. Got any ideas?
2 replies
RRCRat Rig Community [Unofficial]
•Created by Dom Dell Computer on 11/1/2024 in #ratos-support
Print freezes, unrecoverable.
Came home last night to the printer in a frozen state. It was not pasued but it was not printing. I was about three layers into it
60 replies
RRCRat Rig Community [Unofficial]
•Created by Dom Dell Computer on 5/30/2024 in #fix-my-printer
Rapido V2 with 104NT smoking and Generally overheating, EBB36
Ive been having this issue right off the bat with two Rap V2s. V1 in the same spot worked ok. I replaced the thermistor and wrapped the wires in kapton to no avail.
19 replies
RRCRat Rig Community [Unofficial]
•Created by Dom Dell Computer on 5/21/2024 in #fix-my-mesh
IDEX 500 weird mesh evolution
So I have come back to my Vcore. First mesh is what I measured previsouly (March?). I cam back today to this mesh. Saw my x gantry rail was loose and it improved in some ways. Third pic is my current sitz
2 replies
RRCRat Rig Community [Unofficial]
•Created by Dom Dell Computer on 4/2/2024 in #fix-my-mesh
Seems I have over compensated. How close is good for a 500?

14 replies
RRCRat Rig Community [Unofficial]
•Created by Dom Dell Computer on 3/24/2024 in #ratos-support
pi 5 Ratos support or workaround
Anyone know how to get ratos to work with the pi 5?
2 replies