Teo_ Posts - Answer Overflow

Teo_

Posts Comments

RRCRat Rig Community [Unofficial]

•Created by Teo_ on 11/16/2024 in #ratos-support

How to set the correct camera to VAOC?

4 replies

RRCRat Rig Community [Unofficial]

•Created by Teo_ on 11/14/2024 in #fix-my-print

Pressure advance issue? Other?

3 replies

RRCRat Rig Community [Unofficial]

•Created by Teo_ on 11/9/2024 in #ratos-support

VAOC issue (x offset on T0) after last RatOS update

82 replies

RRCRat Rig Community [Unofficial]

•Created by Teo_ on 11/6/2024 in #fix-my-printer

Frequent tangle detection on Smart filament sensor for Orbiter 2 on V-Core 4 400 IDEX

My prints fails due to frequent tangle detection, specially with opaque filament. I can read on Orbiter page: "The detection is activated when filament the pulling force is increased over 1.5–2 kilograms of force for more than one second. The wear of PTFE tube can also trigger tangle detection due to the high friction force. Warning!!! The tangle detection can be falsely triggered by high friction in a long PTFE tube, hard-turning big filament spools, or high printer acceleration with an improperly secured PTFE tube." https://www.orbiterprojects.com/smart-sensor-for-orbiter-v2/ But if I manually restart the print, it proceeds for some minutes untile the next tangle detection. Do you think the "pulling force" or the "one second" can be changed in configuration to reduce the false positives?

16:06
RatOS | DEBUG - RESTORE_TOOLHEAD_SETTINGS:
Toolhead settings restored. 2500.0 accel, 0.5 ratio, 800.0 velocity, 5.0 scv.
16:06
RatOS | DEBUG - RESTORE_TOOLHEAD_SETTINGS:
Toolhead settings restored. 8000.0 accel, 0.5 ratio, 36000.0 velocity, 5.0 scv.
16:06
RatOS | DEBUG - SET_MACRO_TRAVEL_SETTINGS:
Macro travel settings set. 8000 accel, 36000.0 velocity
16:06
RatOS | DEBUG - CACHE_TOOLHEAD_SETTINGS:
Toolhead settings cached for park. 8000.0 accel, 0.5 ratio, 36000.0 velocity, 5.0 scv.
16:06
RatOS | DEBUG - PARK_TOOLHEAD:
Parking T1..
16:06
RatOS | DEBUG - PAUSE:
z_speed: 900.0, pause_print_park_x: , pause_print_park_in: front, default_toolhead: 0
16:06
RatOS | DEBUG - SET_MACRO_TRAVEL_SETTINGS:
Macro travel settings set. 8000 accel, 36000.0 velocity
16:06
RatOS | DEBUG - CACHE_TOOLHEAD_SETTINGS:
Toolhead settings cached for pause. 2500.0 accel, 0.5 ratio, 800.0 velocity, 5.0 scv.
16:06
RatOS | DEBUG - PAUSE:
idex_mode: primary, idex_toolhead: 1, idex_toolhead_x: 198.476, idex_toolhead_y: 257.55, idex_toolhead_z: 0.55
16:06
RatOS | DEBUG - _ON_FILAMENT_END:
TOOLHEAD: 1
16:06
RatOS | DEBUG - _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG:
TOOLHEAD: 1

16:06
RatOS | DEBUG - RESTORE_TOOLHEAD_SETTINGS:
Toolhead settings restored. 2500.0 accel, 0.5 ratio, 800.0 velocity, 5.0 scv.
16:06
RatOS | DEBUG - RESTORE_TOOLHEAD_SETTINGS:
Toolhead settings restored. 8000.0 accel, 0.5 ratio, 36000.0 velocity, 5.0 scv.
16:06
RatOS | DEBUG - SET_MACRO_TRAVEL_SETTINGS:
Macro travel settings set. 8000 accel, 36000.0 velocity
16:06
RatOS | DEBUG - CACHE_TOOLHEAD_SETTINGS:
Toolhead settings cached for park. 8000.0 accel, 0.5 ratio, 36000.0 velocity, 5.0 scv.
16:06
RatOS | DEBUG - PARK_TOOLHEAD:
Parking T1..
16:06
RatOS | DEBUG - PAUSE:
z_speed: 900.0, pause_print_park_x: , pause_print_park_in: front, default_toolhead: 0
16:06
RatOS | DEBUG - SET_MACRO_TRAVEL_SETTINGS:
Macro travel settings set. 8000 accel, 36000.0 velocity
16:06
RatOS | DEBUG - CACHE_TOOLHEAD_SETTINGS:
Toolhead settings cached for pause. 2500.0 accel, 0.5 ratio, 800.0 velocity, 5.0 scv.
16:06
RatOS | DEBUG - PAUSE:
idex_mode: primary, idex_toolhead: 1, idex_toolhead_x: 198.476, idex_toolhead_y: 257.55, idex_toolhead_z: 0.55
16:06
RatOS | DEBUG - _ON_FILAMENT_END:
TOOLHEAD: 1
16:06
RatOS | DEBUG - _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG:
TOOLHEAD: 1