Teo_
RRCRat Rig Community [Unofficial]
•Created by AOne on 3/10/2025 in #fix-my-print
IDEX offset of T1 on the far side from VAOC
I had the same issue https://discordapp.com/channels/582187371529764864/1342875001266634854 and loosening the Y-axis tensioners fixed it.
22 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/22/2025 in #fix-my-print
IDEX offset but VAOC calibration was OK
Fixed 🙂
20 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/22/2025 in #fix-my-print
IDEX offset but VAOC calibration was OK
I started with the GATS procedure with 3 kg and then, print after print, I am loosening the Y-axis tensioners and the offset is improving
20 replies
RRCRat Rig Community [Unofficial]
•Created by Volgger on 3/14/2025 in #fix-my-printer
Strange noise :-)
In can be the same issue: https://discordapp.com/channels/582187371529764864/1345780738200567910
5 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/22/2025 in #fix-my-print
IDEX offset but VAOC calibration was OK
Thanks. Once finished some prints, I'll try retensioning everything using this https://discordapp.com/channels/582187371529764864/1246891806520639552/1333148767251337236
20 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/22/2025 in #fix-my-print
IDEX offset but VAOC calibration was OK
20 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/22/2025 in #fix-my-print
IDEX offset but VAOC calibration was OK
20 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 3/2/2025 in #fix-my-printer
What is this click moving x axis? A dead bearing?
By tightening the two screws of the pulley, the problem seems to have been solved
14 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 3/2/2025 in #fix-my-printer
What is this click moving x axis? A dead bearing?
14 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/17/2025 in #ratos-support
Chamber heater settings question
It works, thanks:
15 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/17/2025 in #ratos-support
Chamber heater settings question
What is the correct command? I’ve tried but…
15 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/17/2025 in #ratos-support
Chamber heater settings question
Ah, OK, so it's only the slicer that defines the chamber temperature, I can't set it manually. Thanks
15 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/17/2025 in #ratos-support
Chamber heater settings question
15 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/22/2025 in #fix-my-print
IDEX offset but VAOC calibration was OK
20 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/22/2025 in #fix-my-print
IDEX offset but VAOC calibration was OK
20 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/22/2025 in #fix-my-print
IDEX offset but VAOC calibration was OK
I’ve tried but after a
SET_SKEW CLEAR=1 I get AC=140,85 and BD=140,87 so I don’t think this is the issue20 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/22/2025 in #fix-my-print
IDEX offset but VAOC calibration was OK
OK, I’ll try
20 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/22/2025 in #fix-my-print
IDEX offset but VAOC calibration was OK
Printed with PETG on V-Core 4.0 IDEX sliced with PrusaSlicer 2.9.0
20 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 2/17/2025 in #ratos-support
Chamber heater settings question
You are right, it is already dead and indicates -21°C 🤦♂️. A better place to monitor the heater temperature for the next sensor?
15 replies
RRCRat Rig Community [Unofficial]
•Created by Teo_ on 12/6/2024 in #ratos-support
Camera stream lost after last Mainsail update
Using process @CrashTestCharlie / VC4 400h CPU affinity setting https://discord.com/channels/582187371529764864/1246891883154640970/1295442351753531412 I can use again webrtc
8 replies