DJDupid
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 11/30/2024 in #ratos-support
BalenaEtcher older versions give malware errors on mac and shutdown.
Since the new versions of balena etcher never work for flashing and I had to resort to older versions to flash ratos2.1 and all of a sudden when I go to redo my chonk the older versions are closing with a malware error and putting the app in the trash. Rasberry pi imager writes the image but I never see ratos coe up in my wifi. With balenaetcher is came right up afterwords but now I cant use it.
26 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 11/5/2024 in #ratos-support
TMC error upon start up of my VC4.
9 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 10/30/2024 in #ratos-support
Chonk Triple Z Beta testing. Need help
43 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 10/23/2024 in #ratos-support
Chonk needs coding for 3 axis Z-tilt
109 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 10/22/2024 in #ratos-support
My homing sequence seems to exclude the rear motor upon lifting to check the z.
I posted this in fix my printer but not many eyes there. This seems to be configuration related. When I first click home all three motors lower the bed. It then homes X and Y then Z goes to home only the two side motors lift and the rear stays.
https://youtube.com/shorts/BwLV4EklHzw
10 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 10/21/2024 in #fix-my-printer
My New Chonk build rear z motor doesn't move during homing.
The bed lowers with all three motors at the start of the homing sequence but then after it checks the x and y motor it goes to lift up for the z probe but the rear doesn't move and the bed binds up. https://youtube.com/shorts/BwLV4EklHzw
19 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 10/18/2024 in #ratos-support
Option 'endstop_pin' in section 'stepper_x' must be specified
67 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 10/17/2024 in #ratos-support
I don't see it anywhere but does ratos support rasberry pi 5?
I just purchased a 5
9 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 10/14/2024 in #ratos-support
Where do you put the wifi login for a rasberry pi 4b with 2.1?
22 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 7/19/2024 in #ratos-support
EBB 42 2 port hotend fan isn't working.
I have double checked this with a second fan but my hotend fan doesn't turn on. This seemed to have happened after I switch to 2.1
8 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 7/13/2024 in #ratos-support
Where is RatOS 2.1?!!!!!
I see the cb1 image for ratos 2.0 which takes you to the old install wizard but cant for the life of me right now figure out why I don't see a single thing for ratos 2.1
75 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 7/13/2024 in #ratos-support
Error when trying to flash ratos 2.0
12 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 7/6/2024 in #ratos-support
Is the new BTT CB2 compatible with ratos?
I want to upgrade my manta m8p to the V2 and seeing if the CB2 is ok to bundle with it?
9 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 6/28/2024 in #ratos-support
4 pin Part cooling Fan not turning on.
I have a vcore 3.1 with eva 2.0 head. I uncommented the 4 pin fan header for the part cooling fan in both 25khz and 100hz but nothing. I have a manta m8p v1.1 and its connected to fan5
50 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 6/25/2024 in #ratos-support
Has any used the adxl built into the EBB42 for input shaper?
I have the EBB42 with the adxl built in and am wondering how I would go about getting ratos to see it. I uncommet the adxl in printer.cfg but then get an error that is isn't connected.
9 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 6/23/2024 in #ratos-support
Help! How do I make my IP static?
Sorry if this has been asked before but my IP changes everytime I turn on my printer.
5 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 6/20/2024 in #ratos-support
Endstop z still triggered after retract
Hello everyone! I finally got my printer moving after cheap bearings and belts were swapped. When I home the printer it homes both the x and y endstops then stops giving me an error saying 'Endstop z still triggered after retract" after. My probe stays triggered and I am scratching my head trying to narrow things down. For context I have an amazon no name inductive probe that I purchased just to get my printer running. I got a euclid probe but didn't feel comfortable yet adding that. I see the beacon probe is now a favorite. Any help is appreciated.
4 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 4/16/2024 in #ratos-support
Toolhead not connecting
250 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 4/6/2024 in #ratos-support
EBB42 cooling fan has 4 pins but the EBB only has 2 pin slots
Any suggestions? I see two slots for fans on the ebb and both are two pins. I don't see many 4028 axial fans with two pins. Could I somehow convert the l2c slot which is 4 pins?
21 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 4/6/2024 in #ratos-support
Who here runs an SSR with a BTT Manta M8P?
I see for the octopus documentary it shows a SSR for the bed but for the manta M8P it doesn't inlude it in the image. Now I am confused if I should wire it in or not.
69 replies