cm
RRCRat Rig Community [Unofficial]
•Created by cm on 12/20/2024 in #fix-my-print
Wiggly Walls
Here are some pitures of the prints I am getting. The walls at an angle have these weird wavy/bumpy artifacts. Any ideas what whese are caused by? Its generic PLA and the outter walls are printed at a slow 40mm/s.
5 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 11/28/2024 in #fix-my-print
Uneven Walls, Please Help!
2 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 10/31/2024 in #ratos-support
TMC ‘extruder’ reports GSAT
6 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 10/25/2024 in #fix-my-print
Weird Artifacts
7 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 10/9/2024 in #ratos-support
Random Pauses? Please Help!
32 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 8/21/2024 in #fix-my-print
Ripple in Pressure Advance Tower
So I have been tyring to tune my pressure advance, but all of the corners look bad. They have this odd ripple like affect that you can see in the pictures below. Any idea what could cause this and how to fix it?
8 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 6/13/2024 in #fix-my-print
Vcore 4 endless ringing
72 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 6/11/2024 in #ratos-support
Motor not turning when homing x axis
Hey guys, I have my vcore 4 built, but I have a strange problem where the bottom right motor doesn't turn when homing the x axis, but does turn when I home y? I am using ratos 2.1.
Here are my printer.cfg and klippy.log plus a video of the problem. https://drive.google.com/file/d/1okLJwd80So2gfhfrPTJrZMNHLKTB02ms/view?usp=sharing
I have checked and all of the steppers appear to be in the right slots too.
7 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 1/7/2024 in #fix-my-print
First Layer Issue with Beacon
17 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 1/6/2024 in #fix-my-printer
Beacon Probe Causing Uneven First Layer?
18 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 12/28/2023 in #fix-my-mesh
Beacon Out of Range
7 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 10/7/2023 in #fix-my-print
Endless Layer Shifts
3 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 10/2/2023 in #fix-my-print
Vertical Banding Appears
2 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 8/29/2023 in #fix-my-mesh
BL-Touch Failed To Deploy
Hello, so I finally have my 500mm v-core 3.1 setup and i am havig an issue with the bed mesh. The bl-touch probe will not be able to deploy at some points during the bed mesh because it is too close to the bed. How can I fix this? I tried the horizontal_z_move but it never did anything. I have attched my printer config below and hope you can help!
4 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 7/6/2023 in #fix-my-print
Horizontal Artifacts?
22 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 6/29/2023 in #fix-my-printer
Hotend Reading Off
8 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 6/21/2023 in #ratos-support
Klipper Can’t Connect To Moonraker
21 replies
RRCRat Rig Community [Unofficial]
•Created by cm on 6/17/2023 in #ratos-support
Klippy Host Software Can't Connect
I just set up my ratrig vcore 3 with rasberry pi 4 and BTT octopus V1.1 board. I have been trying to get it working, but after following the setup guide, I setup the firmware, flashed it, but after editing the printer.cfg step, I get the message "Printer is not ready, The Klipper host software is attempting to connect. Please retry". I have restarted the printer and firmware but it doesnt change. ANy advice? Im pretty new to klipper so its been challenging. Thanks!
12 replies