Toolhead Beta-400
Just did the FMMM, motor dampener, funnsor XY joiners, and switched to the toolhead beta 2. How do these graphs look?
VC3.1 500. I am getting some belt binding
Looking for some help with belt tension. My belts are binding and I think that is messing with my bed mesh.
Also, I'm unsure how to read the graph and how to fix the noise....
vcore 300 Not sure how to input the proper values
So here are my charts, but i'm struggling inputting the values. I feel like i'm doing what the commissioning guide says but it errors out when rebooting after saving
Vcore 400
My setup: Funssor CF Tube, VZ-Printhead, Goliath air-cooled, Beacon RevH, BRS M1, Motor Decoupler + FMMM
Have triple check that all my screws on the printhead is secured, tried detaching wire loom from print head without any success. Tried increasing and reducing tension, doesn't help. There seems to be a persistent resonance over a large band in the y-axis direction, from 75hz to 133hz.
Need help from any expert over my terrible skills...
V-minion speed
Does anyone know how can I increase the max speed with input shaping on Y, at the moment it is 9400, the belts are tight and vibration look okay. What other thinks could I tweak? Thanks in advance
Vcore 400 graphs
Hi everyone.
I have just upgraded the belts and bearings oon my V-Core 400 and have spent the last few evenings playing with the belt tensions. It seems at the moment that I am not getting consistent results. I was chasing my tail a bit and adjusting per the individual result and re-testing, but have just found that if I ran the same test over a few times, the results were quite different which seemed strange. Has anyone had similar at all in the past?
I have attached two pics from the X/Y belt tension results with no adjustments to the belts between the tests, and have also attached the shaper graphs.
...
VC3.1 500mm Enc 2.0 BRS AWD Ti Gantry Tube Belt Tension
I'm looking for some help regarding my belt tension. I'm assuming this is too much tension?
Printer Specs Below
VC3.1 500mm + Enclosure 2.0
BRS AWD Kit @BRS-ENGINEERING-Florent Broise ...
VC3-300
I tried to adjust the belt tension for the last hours, but somehow I can't get behind whats causing the first hump at around 50Hz in the belt tension.
The tension is pretty strong (much more than before mounting FMMM and new belts).
Also, the resonance on X is much higher than on Y.
Could you please help me interpret the problem? (at least I think there is a problem)...
Cant find the issue between 75 and 140 HZ
Ive an Ratrig VCore 3.1 400 enclosed with the new toolhead
and i cant find the reason why i have that Belt graph...
Vcore 3.1 400mm, does this look right?
Im trying to understand the resonance graphs but its going over my head just a little bit.
Does this look like under tensioned belts to you?...
Does this look like under tensioned belts to you?...
Can someone decode this for me?
Brand new IS results with new rr toolhead.... I have no idea what any of this stuff means. Can someone just take a quick look and tell me what you think?
This is a vcore 3.1 500 with rat rig toolhead, beacon, rapido, and orbiter 2....
Y is ok but X is not, help please
A little help please, in Y is fine but in X not so much haha, what can I do to improve I saw the video but I have not been able to solve it yet.
https://www.youtube.com/watch?v=M-yc_XM8sP4
...
I wonder if the Hertz is low? (v-core 3.1/500)
🤔
A friend told me that the curves are smooth but the hertz is low. it would be great to hear your suggestion....
X looks great, Y like ****
Hey guys,
trying to fix my input shaping right now. X looks good I think, but Y is another story. I tried tightening and loosening the belts one at a time, made sure everything is aligned and alls screws are tightended down. Im out of Ideas, maybe you guys can help me with my Y graph. Thanks (Pics attached)...
V-Core 300 3.1 enclosed
RatRig Toolhead v2, EBB42 1.2 with adxl
Need help to understand, How do my graphics look?...
Strange peak on y
Hi, My X axis looks good, but on Y I have strange peak. I was trying different accelerometers, but result is the same - on nozzle, on cartographer.
Any ideas how can I get rid of it ?
Printer: VZ235;...
