shifubrams
shifubrams
PostsComments
RRCRat Rig Community [Unofficial]
Created by shifubrams on 10/9/2024 in #fix-my-resonance
vc3.1 400 impossible to align both peaks
No description
16 replies
RRCRat Rig Community [Unofficial]
Created by shifubrams on 7/18/2024 in #ratos-support
No more correct print since update 2.1
hi , since i updated to ratos 2.1 i have a lot of stringing and can't print a complete piece as it finished to clog. My printer : Vcore 3.1 enclosed LGX Large with reinforced metal gears Mosquito magnum cht bimetal retraction tried 0.3 0.4 and 0.5 same issues different filaments tested that where dryed didn't have those issue before the update configuration of the extruder : [tmc2209 extruder] uart_pin: e_uart_pin run_current: 0.45 stealthchop_threshold: 0 interpolate: False [extruder] dir_pin: e_dir_pin # Remove ! in front of pin name to reverse the direction of extruder rotation_distance: 8 # Bondtech LGX default max_extrude_only_distance: 200 nozzle_diameter: 0.4 heater_pin: e_heater_pin sensor_type: ATC Semitec 104GT-2 sensor_pin: e_sensor_pin min_extrude_temp: 170 min_temp: 0 max_temp: 285 pressure_advance: 0.03 I'm lost... i kept all the config files from my previous installation 2.0.X so i did put everything as it was. Also loading a filament make a weird noise, here is a video :
55 replies
RRCRat Rig Community [Unofficial]
Created by shifubrams on 5/2/2024 in #fix-my-print
flow or z move issues
No description
3 replies
RRCRat Rig Community [Unofficial]
Created by shifubrams on 4/23/2024 in #fix-my-printer
parts cooling fan is going on and off during print.
Hi, The 4028 fan is having a weird behavior. During long prints it goes on and off randomly. When I check the UI, it stays at 100%. Here is a video showing that behavior
9 replies
RRCRat Rig Community [Unofficial]
Created by shifubrams on 12/21/2023 in #fix-my-printer
issue with deploying probe
Hi, The printer is making beautiful prints and I'm happy with it. But sometimes if my toolhead is on 400x 400y and I run the probe deploye ( Euclid ) the motors seems to fail steps. Here is a video for demonstrating the issue. I'm running at 4500mm/s
17 replies
RRCRat Rig Community [Unofficial]
Created by shifubrams on 8/18/2023 in #fix-my-resonance
V-Core 3.1 enclosed 400 interpretation of graphs
No description
35 replies
RRCRat Rig Community [Unofficial]
Created by shifubrams on 8/3/2023 in #fix-my-print
stringing
No description
3 replies
RRCRat Rig Community [Unofficial]
Created by shifubrams on 7/28/2023 in #fix-my-printer
Stepper motors noise when enabled without moving.
My z front left is making a weird noise once enabled. It's the only one that makes this noise. Other motors are quiete when not moving... is it normal ?
14 replies
RRCRat Rig Community [Unofficial]
Created by shifubrams on 7/24/2023 in #fix-my-printer
Trouble to flash my octopus v1.1 f446 on DFU mode. detected but not responding
Hi everyone, I'm having trouble to flash my octopus v1.1 f446 on DFU mode.it starts flashing then after querying it says "Octopus v1.1 detected but not responding" Jumper is set on power via USB and on boot0.
10 replies