Abrupt dip in the middle of the plate - Vcore3.1 400
Are these kind of holes in plain middle of the plate very usual? 0.176mm in this one spot seems a bit rough.. Is there anything I can do to improve it?
V-Core 500. X Axis
Here is my height map. I have watched the video and didnt see my specific mesh as an example.
I spent a lot of time making sure the frame was true and square.
As you can see the lines between the three axis points are in the same plane but the rear corners seem to sag. there is nothing loaded on the plate corners so i am guessing it is the beds own weight. is there a remedy for this?
I let the system warm up and then losened the X-Axis and retightened after and the mesh didn't change. I didn't do the same with the Y-Axis but i see that maybe that could help?
I understand i could fill the corners with kapton tape as a last resort but wanted to check in first....
Hints for Improvement
Any ideas on how to improve this?
I am going to adjust the front idler position to fix the high/low front corners but would like advice on:
1. The blue spot on the left - this causes the most pain with getting a decent first layer across large prints...
first layer
Hey, need help, not sure what I`m doing wrong, in it start prin firstlayer nicely ( bottom left) but then it is not nice. thanks for help
Y Axis Bow, how to fix?
I'm getting bowed mesh along the Y axis and i'm not sure how to fix it. Appreciate if someone can guide me
Needing help reducing range
After watching this video: https://www.youtube.com/watch?v=h7ZTq2dDTkM
It seems that my issue is mainly with the gantry, which I'll approach again soon.
My main question is around the back corners. In the video he mentions that the front corners will always be on the same plane, because for each of those corners there steppers/rods adjusting them directly. He then mentions something along the lines of adjusting to get the back corners on the same plane. What i'm wondering is, it appears that my back corners are on the same plane. My novice observation is, if the front raised, wouldn't my range/variance in height go down? Am I misunderstanding something here?...
bed mesh spike on vcore v3.1 300mm
Hi
I am going to be doing some large prints on my 300 and need the bed to be as flat as possible to avoid warping ,so I did a 15x15 probe count bed mesh to see how bad it was .
Anyway I know the height maps can seem worse than they actually are and I have a crazy spike in the left front corner and I am wondering what I need to do to sort it or should I just leave as is.
Any help gratefully appreciated thank you....
[Fixed]Sides sagging once enclosure is heated up
So been squaring and i know i am within the 0.2 region. But results could be improved dramatically if i figure out the x axis drop in the first line.
This is a room temperature mesh btw....
Z-tilt not correcting tilt along Y axis
You can see a clear slope trend along Y axis. The front two corners are nearly the same, and the back two corners are nearly the same, but Z-tilt should be making them level, but it is not. There is also gantry bowing but I can't really do much about that
Bed mesh on Vcore3.1 500
Hi everyone,
Can someone guide me through acceptable bed mesh deviation on a 500?...
Corner dip. Bed level with PAM. Uneven first layer. i.e. perfect layer one side, opposite too close
I have a problem that when laying the first layer, it does not seem like PAM does anything or not enough to make the layer perfect..
Do anyone know what is wrong here?
And how it can be fixed?...
Rear corner dip
I've been wrestling with this for hours now, after having installed the Enclosure kit earlier today - each adjustment I make seems to throw something out of whack. I'm sure I can improve on this since the tolerance before installing the enclosure was about .19mm. I have been unscrewing the left and right extrusions and adjusting them up and down to try and bring it into square as detailed in the FAQ video, and measuring my adjustments with a caliper just to make sure I'm not going mad - any idea...
New Bed Plate
Just installed new bed plate from Mandala, will the RR clean up this variance with a bed mesh or by running PAM before each print? Flatter bed picture is of new Mandala bed, wavy photo is of old RR stock bed.
First Mesh hot off the press
How am I looking? Is a variance of 0.179 good enough? This is without a magnet and plate on the bed. So I guess I just need to make sure this is good enough to proceed with actually finishing the build first. 😅
Sanity check
Hello. Just a sanity check. The front right (audience side) needs to go up a bit, correct?
