NightLink42 Posts - Answer Overflow

NightLink42

•Created by NightLink42 on 1/7/2025 in #ratos-support

Skipped steps on Y-axis with Sensorless Homing

Hello, V-Minion 1.0 Noticed today that, when enabling sensorless homing on Y-axis, when it's done and attempts to returns to center, the motor massively skips steps and barely moves when in performance mode. Changing back to a Physical Endstop doesn't have this problem. I believe that after it's done homing, it doesn't go back to normal current, hence the skipped steps. Connected to MOTOR Z 2 on LDO Leviathan v1.2 Driver: LDO TMC2209 Motor: LDO-42STH40-1684AC Voltage: 24

2 replies

RRCRat Rig Community [Unofficial]

•Created by NightLink42 on 1/1/2025 in #ratos-support

Bed temp on Leviathan

Hello. I just switched from a Octopus 446 to Leviathan on my Minion. Everything is working great so far, but my bed temp is off. Shows 6c when it should be about 20c (same as extruder). Just out of curiosity I switched the hotend and bed wiring and the bed is showing correct in the hotend side, but now the hotend is showing around 6 in the bed side Everything is fully updated as far as it'll go. Any ideas? Thanks!

21 replies

RRCRat Rig Community [Unofficial]

•Created by NightLink42 on 2/1/2024 in #ratos-support

Z tilt goin NUTS with beacon

Hello, V-Core 3.1 500 Toolhead Beta 2 with latest Beacon Revision added This has weirdly happened to me twice tonight. While tilt adjusting my printer just decides to go crazy and move z on one stepper by a 180+. No idea why this is happening but thankfully I've been able to catch it. Before it happens I'll get a "Empty clusters found" error, so I cancel the print, start it again, and then this.....Any ideas?

8:57 PM
Shutdown due to webhooks request
8:57 PM
Shutdown due to webhooks request
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown
8:57 PM
Probing failed due to printer shutdown
8:57 PM
Probing failed due to printer shutdown
8:57 PM
Probing failed due to printer shutdown
8:57 PM
Probing failed due to printer shutdown
8:56 PM
Retries: 1/10 Probed points range: 3.757149 tolerance: 0.020000
8:56 PM
Klipper state: Shutdown
8:56 PM
Making the following Z adjustments:
stepper_z = 2.043652
stepper_z1 = -3.983295
**stepper_z2 = 189.862566**
8:56 PM
probe at 0.000,0.000,0.000 is z=1.954288
8:56 PM
probe at 250.000,460.000,1.972 is z=1.957593
8:56 PM
probe at 10.000,0.000,3.752 is z=1.949405
8:56 PM
Retries: 0/10 Probed points range: 1.865992 tolerance: 0.020000
8:56 PM
Making the following Z adjustments:
stepper_z = -1.993516
stepper_z1 = -0.047897
stepper_z2 = -0.045235
8:56 PM
probe at 480.000,0.000,1.862 is z=1.946356
8:56 PM
probe at 250.000,460.000,1.872 is z=1.958792
8:56 PM
probe at 0.912,0.410,0.000 is z=1.950301
8:56 PM
Adjusting Z tilt...
8:56 PM
Pre-heating extruder...
8:56 PM
Heating bed...
8:56 PM
All requested axes already homed, skipping..

8:57 PM
Shutdown due to webhooks request
8:57 PM
Shutdown due to webhooks request
Once the underlying issue is corrected, use the
"FIRMWARE_RESTART" command to reset the firmware, reload the
config, and restart the host software.
Printer is shutdown
8:57 PM
Probing failed due to printer shutdown
8:57 PM
Probing failed due to printer shutdown
8:57 PM
Probing failed due to printer shutdown
8:57 PM
Probing failed due to printer shutdown
8:56 PM
Retries: 1/10 Probed points range: 3.757149 tolerance: 0.020000
8:56 PM
Klipper state: Shutdown
8:56 PM
Making the following Z adjustments:
stepper_z = 2.043652
stepper_z1 = -3.983295
**stepper_z2 = 189.862566**
8:56 PM
probe at 0.000,0.000,0.000 is z=1.954288
8:56 PM
probe at 250.000,460.000,1.972 is z=1.957593
8:56 PM
probe at 10.000,0.000,3.752 is z=1.949405
8:56 PM
Retries: 0/10 Probed points range: 1.865992 tolerance: 0.020000
8:56 PM
Making the following Z adjustments:
stepper_z = -1.993516
stepper_z1 = -0.047897
stepper_z2 = -0.045235
8:56 PM
probe at 480.000,0.000,1.862 is z=1.946356
8:56 PM
probe at 250.000,460.000,1.872 is z=1.958792
8:56 PM
probe at 0.912,0.410,0.000 is z=1.950301
8:56 PM
Adjusting Z tilt...
8:56 PM
Pre-heating extruder...
8:56 PM
Heating bed...
8:56 PM
All requested axes already homed, skipping..

11 replies

RRCRat Rig Community [Unofficial]

•Created by NightLink42 on 1/4/2024 in #fix-my-resonance

Shaper calibration: Fans on or off?

Hello. When running shaper calibration, should the fans be on "as normal" (Ex: Print fan @ 100% and heatbreak fan on) or should they be completely off? I found a reddit post from years ago about it, and there was a response that recommended them being on, but I haven't seen it discussed here or on any official klipper posts

2 replies

RRCRat Rig Community [Unofficial]

•Created by NightLink42 on 8/8/2023 in #ratos-support

Invalid adxl345 id on toolboard

Hello everyone, Printer seems to run fine but every time I run an auto input shaping calibration (through KlipperScreen) I get this

12:50 PM Axes noise for xy-axis accelerometer: 17.007011 (x), 20.538347 (y), 31.433369 (z)
12:50 PM Invalid adxl345 id (got ff vs e5).
12:50 PM Invalid adxl345 id (got ff vs e5).
This is generally indicative of connection problems
(e.g. faulty wiring) or a faulty adxl345 chip.
12:50 PM shaper_type_y:zv shaper_freq_y:53.000 damping_ratio_y:0.100000
12:50 PM shaper_type_x:mzv shaper_freq_x:61.000 damping_ratio_x:0.100000
12:50 PM MEASURE_AXES_NOISE
12:50 PM ACCELEROMETER_QUERY
12:50 PM SET_INPUT_SHAPER

12:50 PM Axes noise for xy-axis accelerometer: 17.007011 (x), 20.538347 (y), 31.433369 (z)
12:50 PM Invalid adxl345 id (got ff vs e5).
12:50 PM Invalid adxl345 id (got ff vs e5).
This is generally indicative of connection problems
(e.g. faulty wiring) or a faulty adxl345 chip.
12:50 PM shaper_type_y:zv shaper_freq_y:53.000 damping_ratio_y:0.100000
12:50 PM shaper_type_x:mzv shaper_freq_x:61.000 damping_ratio_x:0.100000
12:50 PM MEASURE_AXES_NOISE
12:50 PM ACCELEROMETER_QUERY
12:50 PM SET_INPUT_SHAPER

Speficially it's happening when ACCELEROMETER_QUERY is ran Everything seems to work fine. Any ideas?

7 replies

RRCRat Rig Community [Unofficial]

•Created by NightLink42 on 7/31/2023 in #ratos-support

SuperPinda.cfg?

Hello. Hopefully this is an easy question. In my printer.cfg the includes for my probe are set to RatOS/z-probe/probe.cfg. Should I set this to superpinda.cfg? Looks like the only difference is speeds

3 replies

RRCRat Rig Community [Unofficial]

•Created by NightLink42 on 3/29/2023 in #fix-my-print

BAD Z Artifacts on new V Minion