NightLink42
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 1/1/2025 in #ratos-support
Bed temp on Leviathan
Thanks for the help. Appreciate it
21 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 1/1/2025 in #ratos-support
Bed temp on Leviathan
Guess no one else really either uses this board yet or has reported it yet.
I’ll keep tinkering around to see if I find any other weirdness
21 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 1/1/2025 in #ratos-support
Bed temp on Leviathan
No jumpers are available in the board to switch it, and the ratos config photo doesn’t list anything to change. Only jumpers it shows is for the fan voltage
21 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 1/1/2025 in #ratos-support
Bed temp on Leviathan
That worked 🙂 but it should be added as default for the board since it’s supported
21 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 1/1/2025 in #ratos-support
Bed temp on Leviathan
Well that was easy enough lol.
Should I do a pull request for changing that? The board is supported by ratos but the pull up value isn’t correct for the bed temp
21 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 1/1/2025 in #ratos-support
Bed temp on Leviathan
Hmm....They're all with 2k2 ohm pullup resistors. Bed is a Generic 3950 sensor
21 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 1/1/2025 in #ratos-support
Bed temp on Leviathan
It goes up
21 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 2/1/2024 in #ratos-support
Z tilt goin NUTS with beacon
That makes sense then lol. Thanks for the response guys 🙂 updated and it’s working now no issue
11 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 2/1/2024 in #ratos-support
Z tilt goin NUTS with beacon
11 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 8/8/2023 in #ratos-support
Invalid adxl345 id on toolboard
accelerometer values (x, y, z): 74.020594, -9326.594869, -306.438199
7 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 8/8/2023 in #ratos-support
Invalid adxl345 id on toolboard
Just a side note though: I do have the toolboard config uncommented.
7 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 8/8/2023 in #ratos-support
Invalid adxl345 id on toolboard
Great! Thank you so much 🙂
7 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 7/31/2023 in #ratos-support
SuperPinda.cfg?
Good enough for me. Thanks!
3 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 3/29/2023 in #fix-my-print
BAD Z Artifacts on new V Minion
Update: It was for some reason the Lead Screw coupling. Once I removed it and replaced it with a solid one it fixed the prints completely
2 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 3/23/2023 in #fix-my-mesh
V-Minion bed tilt?
6 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 3/23/2023 in #fix-my-mesh
V-Minion bed tilt?
Much better. Thanks boss
6 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 3/23/2023 in #fix-my-mesh
V-Minion bed tilt?
6 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 1/7/2023 in #fix-my-mesh
Sanity check
Sorry. I mean like, I can’t push down the front left down any further
31 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 1/7/2023 in #fix-my-mesh
Sanity check
I’m also using aluminum xy idler/motor mounts. I wonder if that’s making a difference as well. Hmm….
31 replies
RRCRat Rig Community [Unofficial]
•Created by NightLink42 on 1/7/2023 in #fix-my-mesh
Sanity check
The problem is that I’m the front left can’t go down anymore. The extrusions are completely on each other. Should I maybe shave some off of one?
31 replies