NecroDavid
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 12/14/2024 in #fix-my-printer
V-Core 3.1 PT1000 ADC out of range (toolboard fault, unknown cause)
5 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 11/9/2024 in #fix-my-print
Move out of range at print start (V-Core 3.1 500)
2 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 4/6/2024 in #ratos-support
Error after RatOS update
11 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 12/25/2023 in #ratos-support
Secondary EBB42 connection problem
25 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 12/22/2023 in #ratos-support
Stuck at control board flashing
93 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 11/5/2023 in #fix-my-printer
[solved] Move out of range at start of print
Move out of range: 553.863 142.883 0.484 [111604.695]
Occurs at start of print after prime blob. I cannot figure out why it wants to go beyond 500, bounds are set correct in slicer and config, looking inside the G-code cannot find anything suspicious. G-code attached.
11 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 10/29/2023 in #fix-my-printer
[solved] Extremely long wait after prime blob
14 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 10/1/2023 in #fix-my-print
Gradual overextrusion
8 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 9/5/2023 in #fix-my-printer
[Solved] Printer stopping after priming, hotend temperature fluctuates
I have a Goliath hotend.
This goes on and on...
3 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 5/12/2023 in #ratos-support
"Disable Extruder Heater" occurs mid print
4 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 5/12/2023 in #fix-my-print
[Solved] Gaps in between perimeter sharp turns
9 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 4/10/2023 in #ratos-support
[solved] Unexplainable behavior after RatOS 2.0 update
19 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 3/24/2023 in #fix-my-print
What causes these random lines?
10 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 3/13/2023 in #ratos-support
BLTouch Z offset minimum bypass
20 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 1/30/2023 in #fix-my-printer
Printer moves extremely slowly when resuming from pause
My printer moves at only 10mm/s when travelling to the print after resuming. Which setting is responsible for this?
3 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 1/20/2023 in #fix-my-mesh
Z-tilt not correcting tilt along Y axis
11 replies
RRCRat Rig Community [Unofficial]
•Created by NecroDavid on 1/14/2023 in #fix-my-printer
[Solved] All PT1000 sensors showing 13 degrees higher
39 replies