someaction
RRCRat Rig Community [Unofficial]
•Created by someaction on 6/19/2024 in #fix-my-print
z bindin on v-minion?
2 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 4/5/2024 in #fix-my-printer
Sometings wrong with stepper driver?
15 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 11/14/2023 in #fix-my-printer
Option 'serial' in section 'mcu' must be specified
4 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 11/13/2023 in #fix-my-resonance
Changed belts, y axis makes strange reading
12 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 10/19/2023 in #fix-my-mesh
Bad first layer, mesh not compensating as it should
30 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 10/5/2023 in #fix-my-mesh
Increase probe points
If i want to make a mesh thats for example 10x10, do i have to change the relative_reference_index aswell? or can i just put the probe_count in override?
1 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 8/15/2023 in #fix-my-resonance
ringing after IS
18 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 5/20/2023 in #fix-my-print
Cubic infill scrapes
1 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 4/17/2023 in #ratos-support
updating from v1.2.4-1 to ratos 2.0
hi im planning on updating to ratos 2.0. i got some questions. after i flash the sd card. can i just plug in the sd card to the pi and continue, or do i have to disconnect all wires on the btt?
in the guide it says "It is heavily recommended that you flash your board and make sure it is detected in the configurator before you plug in your stepper drivers and start connecting your wiring."
and also, do i have to do anything after all is done? ive saved my printer.cfg, can i just paste it in and go? and a while back i saw someting that the bed_mesh is not going to work. i have not updated klipper after i got that message, but im planning on doing it after i get ratos 2.0 going. what do i need to do with that?
6 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 4/13/2023 in #fix-my-mesh
flipped bed mesh????
3 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 3/16/2023 in #fix-my-mesh
Bed mesh doesnt match up. doesnt compensate right
12 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 2/24/2023 in #fix-my-printer
Heating extruder not heating at expected rate
8 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 1/15/2023 in #fix-my-mesh
first layer is not 100%
ive notice that my first layer is a little off. the right side of the bed is a little to high for some reason. my question is, can PAM mesh fix this? and if so, how do i set it up? today its doing a 3 point mesh for the whole bed. im thinking maybe it will get more accurate if it only make a mesh for the print area, or am i wrong?
1 replies
RRCRat Rig Community [Unofficial]
•Created by someaction on 12/5/2022 in #fix-my-print
Heater extruder not heating at expected rate
193 replies