beacon Probe Sample spread too large
I keep getting this error. I have checked all possible causes multiple times, tightened all screws several times, and inspected everything. When I perform the calibration cold, it works and completes successfully. However, when heating up and the measurement is taken, the calibration fails every time. I have already brought the system up to operating temperature to eliminate deformations, but the problem persists. Any solutions ?
Temperature readings from hotend thermistor wrong/inverted
So I have the ratrig v-core 4 400mm. Did most of the hardware aaaaages ago and only got around to trying to configure the software recently. At powerup the hotend cooling fan ramps up as high as it'll go, and reportted temp in the web interface is 130C. I've removed the jumper to see how that affects it and it then hovers at 150C. Heating up the hotend caused the temperature to drop rather than increase. Is there something configured wrong somewhere?
I've also measured the resistance when not in the system and am getting around 1kOhm, same as another rapido hotend that i just took out of its' box...
Solution:
ahh im an idiot, had the wrong hotend selected in the config
1st layer inconsistency
I'm having trouble getting a good consistent first layer. Sometimes it's ok other time I gotta restart the print. I get some ribboning it's usually after 20-30 lines. Even baby stepping doesn't really fix my issue
What is my belt tensioning graph telling me?
I added a beacon a few weeks ago, and cant seem to get my tension right after.. how come i get 3 peaks? are both at the right tension, but just need a fine tune? or are the to tight or to loose?
I accidentaly took out the metal sheet on top of the bed when I was trying to put axes to home
I am already trying to print the 3d parts that are broken, What steps should i do next?
Printer stopping mid-print
So, my printer just started stopping mid print for no apparent reason, and always stops at the same spot.
At first I thought it was something to do with the sd card but I bought a new one and nothing changed.
There is no errors, no warnings, and the print acts like it still going on but no flow or speed obviously (see image).
...
Input Shaper bad Y
Hey everyone, I just converted a core XY printer to klipper and use the accelometer of a beacon Rev. H for belt tension and Input Shaper. I've fairly got some experience with building 3d printers and also with klipper, but I can't get rid of this 125Hz peak on the Y axis. The X looks absolutely dope with 15k mzv. I aligned and squared the gantry, made sure that belt tension is equal, zip tied everything that could move and checked every screw. I'd like to at least get below 1.5% vib and over 5k...
Linear rail not sitting flat
I'm in pursuit of getting a really solid mechanical starting point, I've always just 'solved it in software' before. This time I'm aiming for a sub 0.1mm spread across the bed, if I can get it.
I'm edging closer with the creation of some jigs to make minor adjustments, but I think I'm now being hamstrung by a linear rail that just doesn't want to sit flat across the extrusion, as per the bed scan image. My feeling is that the low points are likely a cause of the linear rail not sitting nicely, too. As the image shows, the right (as you look at the front of the printer) Y linear rail now seems reasonably well situated/tuned in terms of the frame. Similarly, both corners of the 'left' Y linear rail are close to the same plane.
Any pro tips on resolving this? I'd like to avoid shimming if at all possible. So far, I've been using the standard guide rail jigs, loosening all screws off (except the rear end) and then untightening all the way, before gently tightening down (so as to allow the t-nut to move inside the channel and properly grip), before tightening fully and moving on to the next one. The thought process being that this would prevent any squeezing of the rails between the two end points. Perhaps I should also try starting from the middle and moving out in each direction one by one......
Move Out of Range Error When Measuring T1 Belt Tension
Hi Guys,
this error started popping up every time I try to measure the T1 belt tension on my V-Core 4 IDEX. It didn’t happen before, but it started after I installed all the updates. I have also re-tensioned the belts.
Please take a look at the error message in the attached picture. I have no idea what’s causing it. T0 works without any issues.
...
