Vausch
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/19/2024 in #fix-my-resonance
VCore 3.1 500 belt tensions seem eratic
8 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/17/2024 in #fix-my-print
Proper TPU support settings for clean removal?
I'm printing some cosplay parts making tpu "foam" by having them be all infill and no walls. The first attempt went well but the supports I had to use damaged the print on removal.
The supports are required due to the shape. Im trying out a few different settings like z distance and removing the interface layer.
13 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 9/5/2024 in #fix-my-print
TPU Infill Foam style Prints rapidly get worse in latter half of a print
3 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 5/11/2024 in #fix-my-print
Sagging ASA on overhangs
22 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 3/27/2024 in #fix-my-print
Consistent Z banding pattern on ASA
4 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/27/2023 in #ratos-support
BTT smart sensor pausing after prime blob, doesn't detect runout after.
20 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/21/2023 in #fix-my-printer
BTT Smart Sensor Pauses after Prime Blob, Doesn't detect during print.
5 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 7/29/2023 in #ratos-support
The value 'my_sensor' is not valid for SENSOR
52 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 7/21/2023 in #ratos-support
Input Shaper isn't applying?
I'm probably just missing something in the printer config or forgot to uncomment something but when I ran the accelerometer it didn't apply any of the shapers as far as I could see.
I had to reinstall RatOS and set everything up again.
1 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 6/5/2023 in #fix-my-printer
Extruder Heater not Heating at Expected Rate
I've gotten this error message 3 times in a row and I've noticed the temperature on the extruder seems to be struggling to remain consistent then often will plummet when it starts the prime blob. The furthest it got was about a minute into the first layer on the first of the 3. It started after a successful petg print that I tried to start again.
I checked and the thermistor and heater cartridge are still in place tightly. I haven't made any major changes.
3 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 5/6/2023 in #fix-my-printer
Ugly fronts of prints
5 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 4/14/2023 in #fix-my-resonance
Dual Peaks on Y-Axis Input Shaper
10 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 4/14/2023 in #fix-my-printer
Massive layer shifts
19 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 2/5/2023 in #fix-my-printer
Carriage slowly drifting to rear left
95 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 12/22/2022 in #fix-my-print
Layer shifts and ugly surfaces
4 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 12/14/2022 in #fix-my-printer
X motion jerking in Y direction, losing center.
I tried to start my first print and suddenly when moving in the X direction on the bed the gantry would jerk back in the y axis. If I move in the Y axis it also jerks slightly in the X.
When I tried my first print it lost the center location and ended up attempting to print on the rear right corner of the bed, too.
It's never had an issue with motion up until now and since I put in the first print it's doing it consistently. Video included.
15 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 12/14/2022 in #fix-my-printer
Selecting Load Filament Unloads (LGX Lite)
I was getting ready to run my first print and when I selected "Load filament" on RatOS the LGX Lite unloaded instead. I'm guessing just some wires need to be swapped on the connector? Not sure which ones though.
3 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 12/9/2022 in #ratos-support
Unable to Parse Option 'pid_Kd' in section 'heater_bed'
71 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 12/9/2022 in #ratos-support
Can't install firmware on Octopus v1.1
I've attempted to install the firmware multiple times and the file in the SD card has remained a .bin file.
The dashboard on ratos states there is a klippy-state error and unable toconnect to mcu.
27 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 12/8/2022 in #ratos-support
ratos.local showing blank page
I just installed ratOS 1.2.4, did the configuration and wifi connection, now i'm getting a blank page on the ratos.local browser page. As such I can't install the controller board firmware.
24 replies