Vausch
RRCRat Rig Community [Unofficial]
•Created by Vausch on 3/2/2025 in #fix-my-printer
Print head juts along y when x is moved /vice versa
Solved. It was a loose toothed gear around the stepper.
4 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 3/2/2025 in #fix-my-printer
Print head juts along y when x is moved /vice versa
Actually think it migbt be a stepper Motor. They're not supposed to Move whem they have power going through them, Right?
4 replies
RRCRat Rig Community [Unofficial]
•Created by popoblito on 2/25/2025 in #fix-my-print
Regularly spaced lines on pieces (Z banding?)
I had a similar issue some time ago and it was due to the slicer. Is it set for "inner/Outer" on the wall printing order? That's what caused it for me (orcaslicer).
6 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/17/2024 in #fix-my-print
Proper TPU support settings for clean removal?
So these are just having a curve underneath and unfortunately no otherb position will really work.
13 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/19/2024 in #fix-my-resonance
VCore 3.1 500 belt tensions seem eratic
nuts
8 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/19/2024 in #fix-my-resonance
VCore 3.1 500 belt tensions seem eratic
8 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/19/2024 in #fix-my-resonance
VCore 3.1 500 belt tensions seem eratic
peak spectral density is dropping over time but I don't know if that's good or not.
8 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/19/2024 in #fix-my-resonance
VCore 3.1 500 belt tensions seem eratic
8 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/19/2024 in #fix-my-resonance
VCore 3.1 500 belt tensions seem eratic
8 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/19/2024 in #fix-my-resonance
VCore 3.1 500 belt tensions seem eratic
Tightening the belts seems to cause the upper belt's arc to increase between 25 and 50 while lower belt goes up between 100 and 125.
8 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/17/2024 in #fix-my-print
Proper TPU support settings for clean removal?
what do you recommend there? Increase the fan speed on the interface?
13 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/17/2024 in #fix-my-print
Proper TPU support settings for clean removal?
13 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/17/2024 in #fix-my-print
Proper TPU support settings for clean removal?
Is that "top z distance" in orca? Sorry some of the terminology changes between slicers.
If it's that, it's .3mm. If it's "top interface spacing" it's .5.
As for the support interface fan I think it was disabled cuz I see it at -1% on the filament setting
13 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 10/17/2024 in #fix-my-print
Proper TPU support settings for clean removal?
@Lemcott @Jamin Collins [VC 3.1 400mm]
13 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 9/5/2024 in #fix-my-print
TPU Infill Foam style Prints rapidly get worse in latter half of a print
3 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 5/11/2024 in #fix-my-print
Sagging ASA on overhangs
Sure hope not. I slowed it down to 30-40mm/s
22 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 5/11/2024 in #fix-my-print
Sagging ASA on overhangs
90
22 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 5/11/2024 in #fix-my-print
Sagging ASA on overhangs
Turning cooling off entirely was the only thing that worked. I switched to another piece instead to look better.
22 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 5/11/2024 in #fix-my-print
Sagging ASA on overhangs
Yeah I can get hatchbox for about 10USD a spool if I buy 5 at a time directly.
22 replies
RRCRat Rig Community [Unofficial]
•Created by Vausch on 5/11/2024 in #fix-my-print
Sagging ASA on overhangs
This is true. Hatchbox is cheap and quality from my experience.
22 replies