Just re-tensioned my belts (VCore 400)
Hi everyone.
Just wondering about people's thoughts on the below graph. seems the belts are pretty similar now, but a bit of a hiccup at 125Hz. Should I be investigating further?...
V-Core 3.1 Enclosure 2.0 500mm Belt Tension & Resonance Help
I'm trying to make out what these graphs mean and how to correct them.
I rebuilt my toolhead out of PolyMax PC + heat inserts the other day along with made a revision to my EBB42 mount (in-front of LGX Lite).
I'm planning on tearing down the printer to replace the PETG core components w/ PolyMax PC components over the next few days.
I've been printing mostly high temp ASA, PA6-CF, PC functional prototypes with pretty good luck but want to make sure that I don't repeat something that I shouldn't when rebuilding....
What should I do from here?
vcore3.1 400
I'm not sure I know what I'm doing, so I'm asking you guys for some input...
Weird ~117Hz X Resonance and Belt Tension Graph
I have a Vcore 3.1 500mm that is sitting on the floor. I am getting an odd peak in the X-direction at like 117Hz any ideas?
Additionally my belt tension graph looks a bit odd....I think? Still new to reading these. The peaks seem to line up, but there are 3 of them, is this normal?
Thanks for the help!...
Good/Bad? RR vCore3.0 500
First, I watched the video. I'm not sure how much I understood from it, but think these are ok, but would like someone with actual experience to give their opinion. The peaks match in frequency and "power" pretty well I think. The extra 42Hz "step" going up on the X probably isn't good, I can't remember if he mentioned such an artifact. The stair step down a couple of steps on the Y, probably not good either.
I'll watch the mentioned video again, but not sure I'll pick up on what I need to do. Thank in advance for any critique or advice....
v-minion Y issue
I think X looks quiet good, but Y is a bit strange to me. What could be the reason? I tried to tight all screws, used belt tension meter to adjust belt tension but graphs are still more or less the same...
V-Minion first Run
Hello. this is my first printer with ratos and klipper. setup with orbiter and rapido and eva 3.0 and adxl on toolboard ebb42 and own adxl on the aluminum bed. what do these curves tell you? are these bad? heard something improved or belt adjusted? what do I have to do in the config or where do I have to use this value so that the printer knows the limits? greet andi
What to improve? (vCore3.1 300mm)
Hi,
I just finished building and setting up my vCore3 and ran input shaper, though I am not entirely sure what to look for and how to improve.
Any help would be very appreciated!...
Idk what im looking for here.
looks like Y is pretty good but X still a bit dodgy. idk what to really look for with my belt tension graph, but it looks like X might just have something loose ?????
Need Help improving graphs (EVA3.0 extruder VZBot330 Motion system)
Hey does anyone have recommendations on what I could improve (especially on the Y-Axis), I don't completely understand those graphs yet, also I'm getting some pretty brutal rattling noises from my printhead.
double peaks on Y
Hi, did someone have such graph? Did you managed to fix it? Any ideas why is it so?
Odd resonance shape on VC300
What to do here? There's resonating sound from EVA, I've checked every screw and part, but nothing. I also noticed that a lot of it comes from BLtouch, but without it X-graph doesn't look much better.
What to improve?
Hi, i don't know how to interpret input shaper graphs. Is it ok or not, and if it's not good what to improve? Thanks for help.
Linear movement analysis
Can someone help me with this graphs? I can't find any information about how to "read" them.
I have a vertical pattern on my prints, more visible under 160mm/s....
V-Minion: X Graph good, Y Graph bad
I cannot for the life of me get the Y axis on this thing to tune well. The printer is sitting on a heavy duty shelf with a combination of a concrete paver and a rubber paver underneath it. I've made sure all the screws on the Y assembly are secured, and I've tried adjusting belt tension, but to no avail. The rail moves very smooth without the belts attached, so I know it's not binding.
The ADXL is mounted to the center of the bed with thick VHB tape, so all the readings it's getting are from the center of mass....
V minion X axis wonky graph
Getting graphs like this. Any ideas how to improve them, since that's far from ideal?
300 very odd belt and resonance graphs
I've loosened and tightened the belts three times not and this is hands down the weirdest graph I've come across. thoughts??
V-core 3.1^500 - Fystec rail - weird graphs
Hi all, should I increase tension a bit on the blue lower belt ? This weird twin peaks bothers me. Input shaper results are crap... Any idea ? Thanks in advance.
