NutellaBrot155
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 5/15/2024 in #fix-my-mesh
VC3.1 Enclosed 400
5 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 4/11/2024 in #ratos-support
After reinstalling Ratos,toolboard often looses connection
Should i try reflashing the boards
19 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 3/29/2024 in #german-support
FIrst Layer/Mesh
16 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 2/3/2024 in #fix-my-resonance
VC 3.1 400 Belt tension
8 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 2/2/2024 in #fix-my-printer
vc3.1 400 Belt Tension
2 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 2/1/2024 in #ratos-support
Skew
I recently used the Calilantern from Vector3d and im wondering how the skew profile needs to be named,since in the START_PRINT macro it loads a skew profile "gcode_Macro Ratos" and i looked into it and cant find the variable or comment how the skew profile should be named
13 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 1/20/2024 in #ratos-support
Ebb Adxl chip problems
8 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 12/23/2023 in #fix-my-resonance
I dont rly understand this
45 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 12/22/2023 in #fix-my-printer
Loud rail sounds
I recently installed the toro tube and regreased my rail,their smooth,but as soon as i install the x-gantry the y axis rails are extremely loud and sound like the balls are crunching
1 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 11/18/2023 in #ratos-support
Z-tilt increases Range
Somehow z-tilt increases the tilt intead of making the bed even.z homing and manual movement from z axis works perfectly
7 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 11/18/2023 in #fix-my-resonance
Low x accel
12 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 7/18/2023 in #ratos-support
hotend not heating
Title
6 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 7/18/2023 in #ratos-support
y home in the wrong direction
The stepper moves in the right direction—> lower values = gantry more on the back,but when i home the gantry moves to the front
3 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 7/18/2023 in #ratos-support
bltouch not showing up as probe in endstops
Also my probe does not report as triggered when Query_Probe is used
13 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 7/18/2023 in #fix-my-printer
Bltouch not working
My bltouch isn’t working and is not listed in endstops as probe
1 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 7/17/2023 in #fix-my-printer
Short circuit protection buzzer goes on when moving motors
15 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 7/17/2023 in #ratos-support
Z probe always triggered
13 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 7/17/2023 in #ratos-support
uart pin must be specified
17 replies
RRCRat Rig Community [Unofficial]
•Created by NutellaBrot155 on 7/17/2023 in #ratos-support
Toolboards
arent some toolboards scuffed from btt,or is the supporeted list the known safely toolboards
2 replies