Tracy7734 Posts - Answer Overflow

Tracy7734

•Created by Tracy7734 on 12/12/2024 in #ratos-support

Latest update seems to have broken the Z offset for the Beacon

Configurator runs perfectly but when setting the inital Z offset, RatOS uses the nozzle temperature adjustment as the Z offset rather than the Model Z offset in Beacon model default.

5 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 10/20/2024 in #ratos-support

Error updating RatOS: Git Command 'fetch origin --prune --progress' failed

First time I have run into an update failure.

8 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 7/18/2024 in #ratos-support

Gantry Slams into Front Belt Tensioners

I have everything working so well and I've tried every type of calibration I can find but nothing I do prevents the gantry from slamming into the front belt tensioners when it does the nozzle wipe. Here is what the console shows: RatOS: Auto calibration nozzle wipe with probe result 0.002165627786482105...

112 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 7/11/2024 in #ratos-support

Z tilt with Beacon Probes at 235

I'm mostly just curious why the z tilt with a Beacon probes at 235 and not 200 by the rear z motor?

4 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 7/1/2024 in #ratos-support

Cannot connect to Klipper

Total new install. Updated all packages. Connects to Moonraker but cannot connect to Klipper.

18 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 6/30/2024 in #ratos-support

x endstop help

The Omron endstops supplied with the Vcore 4 are not available anywhere so I’m using cheap Amazon ones to upgrade my tool head. The Omron are closed by default. Will switching the pos and neg when connecting to the EBB42 work as a work around? I’m concerned that if I wire it wrong and the endstop triggers I could blow the board.

7 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 6/29/2024 in #ratos-support

Cannot get 2.1 to work on new install

I followed the RatRig dozuki site precisely regarding all electronics. I wired everything to the EBB42 v 1.2 toolboard and my Octopus v1.1 mcu. I created a totally new micro sd card with the latest version 2.1. I got to the install part where it asked for my toolboard. As expected it needed to be flashed. The automatic flashing did not work nor has any attempt to flash via DFU worked. And I have the 24vdc connected correctly. Brand new v3.1 USB cords. This is my third attempt in the 18 months I have owned a RAtRig to try a toolboard, always with the same outcome. It can't be this difficult. I can't even detect power to the toolboard but now sure what to look for. LIghts?

6 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 1/19/2024 in #fix-my-resonance

Tuning VCore with dual linear rail on gantry

6 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 1/19/2024 in #ratos-support

KlipperScreen Time Display

How do I get KlipperScreen to display correct time. I've tried many ssh commands and nothing has worked even if I set it is ssh with the tzselect tool

5 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 1/14/2024 in #ratos-support

Install RatOS

18 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 12/30/2023 in #ratos-support

Moonraker Warning

Unparsed config option 'primary_branch: v2.x-deployment' detected in section [update_manager ratos-configurator]. This may be an option no longer available or could be the result of a module that failed to load. In the future this will result in a startup error.

2 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 12/30/2023 in #ratos-support

Moonraker Warning

[update_manager]: Failed to load extension ratos-configurator: Invalid path for option install_script in section [update_manager ratos-configurator]: Path /home/pi/ratos-configurator/scripts/setup.sh does not exist

26 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 12/30/2023 in #ratos-support

Moonraker warning

2 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 12/9/2023 in #fix-my-resonance

Input shaper - toolboard

Why does the y show rpi? resonance_tester] accel_chip_x: adxl345 toolboard accel_chip_y: adxl345 rpi

3 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 10/15/2023 in #ratos-support

KUSBA cannot get to work

10 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 7/17/2023 in #ratos-support

Can't get Orbiter filament sensor v2.2 to work properly

Using J28 and J30 filament_switch_sensor filament_sensor] event_delay: 0.1 pause_on_runout: True runout_gcode: UNLOAD_FILAMENT insert_gcode: LOAD_FILAMENT switch_pin: PG12 # green wire [gcode_button sensor_button] pin: !PG13 # yellow wire press_gcode: UNLOAD_FILAMENT

3 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 7/6/2023 in #fix-my-printer

See the 'max_extrude_cross_section' config option for details

Anybody know where this setting is? I couldn't find it in the extruder section. New Orbiter 2.0 and its not extruding so trying to calibrate with Orca.

33 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 7/1/2023 in #ratos-support

Just updated RatOS and now usb web cam does not work

I had it working at one time but cannot remember all the SSH and other changes and I can't find where that information was that I used

26 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 6/30/2023 in #ratos-support

BTT 42 does not flash.

Connected via USB. Octopus V1.1 flashed fine. Boot button, reset button does nothing. Is a second jumper required?

24 replies

RRCRat Rig Community [Unofficial]

•Created by Tracy7734 on 5/20/2023 in #fix-my-mesh

PAM

If we didn't see this before update, what should we do? INFO If you are currently using PAM, you should delete the PAM includes from printer.cfg before proceeding. Afterwards you can delete the PAM directory and remove the PAM moonraker.conf entry.

5 replies

Gaming

Programming