Tracy7734
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 10/20/2024 in #ratos-support
Error updating RatOS: Git Command 'fetch origin --prune --progress' failed
Hard recovery fixed it
6 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 10/20/2024 in #ratos-support
Error updating RatOS: Git Command 'fetch origin --prune --progress' failed
I’m using a fast Ethernet connection.
6 replies
RRCRat Rig Community [Unofficial]
•Created by koekie40 on 8/21/2024 in #ratos-support
i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B
I would also try connecting via Ethernet.
69 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
It works perfectly. 😜
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
Do I delete those same lines above or will Klipper only read the last?
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
It does print a perfect first layer😜
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
So, G0 X0 Y0 hits the front. And ideas?
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
Is the command Go X0 Y0
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
I measured. I have 430mm from endstop to front. Set at 390 and gantry still slams.
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
I thought that might help.
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
And, with all the fixes, my gantry still slams into the front.
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
I didnt use commas.
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
Is G0, X0, Y0 on the command line? That returns an out of range error.
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
It’s just not that easy. I move it back and the beacon tries to scan beyond the bed. I change the y position min and I get out of range error. There must be a very fine line where it will work.
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
I’m crashing on every print attempt. All out of range errors. I did physically move the endstop.
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
Of course, y max, endstop 350 crashed because z tilt goes to 370. More hidden code 😉
112 replies
RRCRat Rig Community [Unofficial]
•Created by Tracy7734 on 7/18/2024 in #ratos-support
Gantry Slams into Front Belt Tensioners
My problem is that I love to tinker. Some just love to print. I’ve probably got $1,000 in upgrades, improvements, etc. Most just ruin good printing.
112 replies