kyle
RRCRat Rig Community [Unofficial]
•Created by kyle on 6/9/2024 in #ratos-support
RatOS and PT1000 B Thermistor
Hello There. I just got a new Rapido Hotend and it is a PT1000B rather than a 104NT-4 like my old one. Can someone help me with what I need to change in the printer config to update this? The current RatOS Rapido.cfg uses “sensor type: ATC Semitic 104GT-2”.
Additionally, I am plugging it into an EBB36 1.2 and have it plug into the TH0 port right now. Since there is only 2 wires, I was unsure if I could use the PT1000 port on the right side of the EBB36 pinout.
Thank you for taking the time to read this!
6 replies
RRCRat Rig Community [Unofficial]
•Created by kyle on 1/21/2024 in #ratos-support
RatOS Z-Offset
Can someone explain to me how Z-Offset works in RatOS? If my nozzle is to close or to far from the bed and I adjust in Mainsail during the print, does it do anything? How can I get a good first layer if it doesn’t seem to adjust while printing?
3 replies
RRCRat Rig Community [Unofficial]
•Created by kyle on 1/5/2024 in #fix-my-print
Lines Across Prints
14 replies
RRCRat Rig Community [Unofficial]
•Created by kyle on 12/22/2023 in #fix-my-resonance
Input Shaper is on, but still getting ghosting
7 replies
RRCRat Rig Community [Unofficial]
•Created by kyle on 12/8/2023 in #ratos-support
12V fan on a 24V Toolboard: Using Klipper and RatOS to reduce power of fan by 50%
Hello, I am looking for some help as the title says, with a 12V Part Cooling fan and a 24V EBB36 toolboard. In RatOS and Klipper, how can I reduce the power of that fan to 50%, therefore the fan will work regardless of the difference in voltage?
2 replies
RRCRat Rig Community [Unofficial]
•Created by kyle on 11/15/2023 in #fix-my-print
HELP! Please review my slicer settings
As the title states, I just want someone to review my slicer settings. I have a RR V-Core 3.1 500 with a 0.6mm nozzle. I haven't gotten a single print out of it yet. I want to use PETG, but since that wasn't working, started using PLA, still to no success.
I have a Bondtech LGX Lite, a Rapido UHF Hotend, a Diamondback Volcano 0.6mm Nozzle, a Beacon Scanner, a EBB36 Toolboard. The resonance is good. The bed level is good.
Here is my printer CFG and Orca Slicer settings. I have kept things like speeds and other things default because I haven't had a chance to tune them as I can't even tune the temperature. The only thing I have done is be able to print a first layer test to ensure I have the correct Z-Offset. I am using Overture PLA but want to use PETG as well after finishing the PLA roll. Esteps have already been done and adjusted using the rotation distance in the printer cfg. I am beyond desparate and so close to quitting. Please help.
I have a Bondtech LGX Lite, a Rapido UHF Hotend, a Diamondback Volcano 0.6mm Nozzle, a Beacon Scanner, a EBB36 Toolboard. The resonance is good. The bed level is good.
Here is my printer CFG and Orca Slicer settings. I have kept things like speeds and other things default because I haven't had a chance to tune them as I can't even tune the temperature. The only thing I have done is be able to print a first layer test to ensure I have the correct Z-Offset. I am using Overture PLA but want to use PETG as well after finishing the PLA roll. Esteps have already been done and adjusted using the rotation distance in the printer cfg. I am beyond desparate and so close to quitting. Please help.
25 replies
RRCRat Rig Community [Unofficial]
•Created by kyle on 11/12/2023 in #ratos-support
Exclude Object
3 replies
RRCRat Rig Community [Unofficial]
•Created by kyle on 11/1/2023 in #fix-my-mesh
Huge Bed Dip! Help!
1 replies
RRCRat Rig Community [Unofficial]
•Created by kyle on 10/30/2023 in #fix-my-mesh
Mesh Suggestions
1 replies
RRCRat Rig Community [Unofficial]
•Created by kyle on 10/30/2023 in #ratos-support
Unknown Pin Chip Name: Probe
102 replies
RRCRat Rig Community [Unofficial]
•Created by kyle on 10/19/2023 in #fix-my-printer
Stepper Motor Direction?
Hello there. I am looking for some help on my X and Y axis of my V-Core 3.1. Here is a video of what is happening when I try to home. I just finished building the printer, so this is right after I turned it on for the first time.
I asked on the Facebook group and they suggested my wiring for the XY stepper motors might be backwards. I have checked the wiring with the RatRig guide and it is correct. I have also gone through belt tensioning and X-Gantry alignment a ton.
With this, someone suggested one of the stepper motors may be moving in the wrong direction. How can I tell this and how can I fix this in RatOS? Thank you for all suggestions and taking the time to read this.
12 replies
RRCRat Rig Community [Unofficial]
•Created by kyle on 10/12/2023 in #fix-my-printer
Help with Belt Tension
Hello there. I’ve got a problem with my machine and the belts. Today was the first time I have turned it on and got Klipper running. Once I did so, I started hiking the X and Y Axis before I figure out the beacon homing.
When I do so, I get a bunch of clicking and stuff like shown in the video. I’m guessing it is an issue with the belt, but I am unsure what! Any pointers and suggestions? Thank you for taking the time to read this.
1 replies