Timmer2019
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 1/22/2025 in #fix-my-print
PETG troubles..
4 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 1/22/2025 in #fix-my-printer
Access to configurator RatOS
Looking to access the configurator page..
Here is my current printer.cgf file:
33 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 12/13/2023 in #fix-my-printer
Retries aborting: Probed points range is increasing.
4 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 3/1/2023 in #fix-my-print
Fan Horns.. really could use some help, please.
16 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 2/27/2023 in #fix-my-print
Reverse Elephant foot..
3 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 2/24/2023 in #fix-my-print
Retraction issue?
1 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 2/16/2023 in #fix-my-print
Rough print on RR Rapido horn
6 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 2/13/2023 in #fix-my-printer
Issues with SAVE_CONFIG
1 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 2/13/2023 in #fix-my-printer
New hot end, incorrect temperature reading with hotend off..
Continued..
9 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 2/8/2023 in #fix-my-printer
Bed level issue?
Wondering if anyone else observed similar issue.. I noticed on doing a first layer print test with prints in various locations on the bed, the first layer print always seems to be thinner toward the front of the bed.. if the BLprobe does the bed levelling test prior to print start, I question why this issue should be showing up..
5 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 2/8/2023 in #fix-my-print
Holes in first layer..
5 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 1/23/2023 in #fix-my-print
What would cause this?
4 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 1/10/2023 in #fix-my-print
Print in PETG
5 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 1/4/2023 in #fix-my-printer
BL Touch calibration, help.
Hey folks I need some help.. trying to calibrate my z axis on ratrig vcore 3.1.. using the paper method I get my nozzle down to provide appropriate friction to paper using the z offset section in rat os.. once I'm happy with the setting I hit save and this automatically updates my printer.cfg file..
It sets the following:
## [bltouch]
## z_offset = 5.240
The problem with this is that any value above 5 gives me the z movement error so I don't think the bltouch value needs to be this high especially when the nozzle, when near touching the bed, the bltouch sensor probe fully retracted is about 1mm away from the bed which is what I want ( I think).. so why does hitting 'save' when I find my optimum nozzle height, set the BL Touch value above 5?
Any help would be greatly appreciated.
Thanks.
Tim
3 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 12/18/2022 in #fix-my-print
Extruder stops several layers in
Hello everyone. I had recently done several big prints with my new printer.. as of recent, I am trying to print a box square for calibration and the print is ruined after several layers due to PLA material no longer extruding.. I can't figure out why.. My assumptions are that the cube layers are quick and extruder can't keep up? I just don't know where to start with troubleshooting this issue.. using superslicer.. any advise would be appreciated.
13 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 12/8/2022 in #fix-my-print
Print warping
12 replies
RRCRat Rig Community [Unofficial]
•Created by Timmer2019 on 12/7/2022 in #fix-my-print
Heater extruder not heating as expected rate..
I received this error during a print.. did a PID test (PID_CALIBRATE HEATER=extruder TARGET=210) and if I use the fan at 100%, the test fails, tried again with fan at 25% and test fails.. tried again at 10%, tests fails.. the only time the PID test worked was with th fan off.. This is a new printer and the test cube printed just fine.. this error happened on another item I wanted to print..
25 replies