small gapes into the top layer asa
Maybe some can help me the small gapes in the top layer next to the holes and at the edge
I did the flow test with the blocks...
bump on outer perimeter in a specific part of the model
SUSL 3mf project with settings is below, the bump appears if sliced with PS as well
overextrusion on top layers
I am running a 3.0 500.
I have tuned the extrusion rate and perimeters are spot on at 0.7mm with a 0.6mm nozzle on Bondtech LGX and Rapido hotend. PA is set at 0.05. Material is MatterHakers ABS. Using PrusaSlicer with the following settings: Topfill pattern: Aligned Rectilinear Top solid infill: 80mm/s...
I have tuned the extrusion rate and perimeters are spot on at 0.7mm with a 0.6mm nozzle on Bondtech LGX and Rapido hotend. PA is set at 0.05. Material is MatterHakers ABS. Using PrusaSlicer with the following settings: Topfill pattern: Aligned Rectilinear Top solid infill: 80mm/s...
Getting these artifacts on my corners.
Okay so the thing i cant wrap my head around is that
1st they are on the same layer each time.
2nd They are on the LEFT side of each corner....
Rough and overly rounded edges.
So far my setup is: VCore 3.1 500, Speed 120mm/s, Acceleration 3500mm/s the y-axis is too heavy and the input shaper shows that my accelerations should be around 4500 . I understand that this part is too small for such a printer, and I also understand that I probably do not have enough acceleration. Nozzle 0.8mm, Hotend Rapido UHF . Trying to just fix problems with the mechanics and raise acceleration?
PA is tunned , i see perfect value at 0.05
Extruder is tuned too....
Baffled Beginner Has Distorted First Print
Nine months after receiving the V-Core 3.1 500 kit, I have finally printed "something", thanks in large part to help from blacksmithforlife us. It's just a very small, very simple calibration .amf file that was created as part of the SuperSlicer_2.4 installation. Attached are 2 images, one showing what S-S says it should look like, and the other is the distorted "thing" printed in PLA. The skirt was also very distorted. The belts are tight, but not like a violin string. The Rig moves quietly and smoothly. I've searched Discord, Facebook, etc. to see if anyone else had this problem, but haven't found anything yet.
Any ideas as to what might be causing this distortion? Help is greatly appreciated. I'm a raw beginner. This is my very first 3-D Printer, and my very first print.
V-Core 3.1 500, RatOS 2.0, Octopus Pro, Raspberry Pi 3 B+, filename: "filament_flow_test_cube.amf". SuperSlicer settings are all the defaults for V-Core 3.1, PLA, etc....
ratrig gantry parts in abs+ warp
I printed them oriented as advised but how is that warped layer supposed to print correctly without supports? Any ideas how I can print those please?
Thanks!...
Artifacts on v-minion in vase mode with 0.6 nozzle
I'm struggling to find why am I seeing artifacts when printing vase mode with a 0.6 nozzle on the v-minion.
- width: 0.85mm
- height: 0.46mm
- max vol. speed 13 mm3/s
- Dragonfly BMO + LGX Lite...
Non consistent infill
What can be the explanation for these gaps in the infill?
Sliced with SuperSlicer. Infill speed was 225, perimeters 160. Slowed it all down to 80%, making infill 175 and perimeters 130, to see if it cleared up, but it didn’t , even though the initial perimeter speed is about the same.
Flow on the infill was at first about 20 mm3, after slowdown about 15 mm3, with a Mosquito Magnum and Orbiter 2.
Edit
Also tried the whole print at 150, gaps are still there. But less then before. Perimeters at 150 are fine....
Layer lines more visible in X axis
I noticed when printing a PA tower that for some reason the Y axis sides looked better than the X axis. It seems to have lines popping. Could this be atributed to the idlers on the xy joiners? When printer moves on Y those stay stationary
overextrusion at beginning of print
Hello,
as you can see in the pictures, I am having issues with overextrusion at the beginning of my prints. Do you have any ideas which setting might cause this?...
Blob on perimeter start after Gap Fill
I have been tackling a issue for some days now, and i was able to pin point in what exact situation it occurs.
Every time there is an extrusion for a Gap fill just before a perimeter start, i get a blob on the start of the perimeter that also translates most of the time to a unveven line of extrusion.
I have tried this with SuperSlicer (2.4.58.5 and 2.5.59.0), tried with PrusaSlicer also....
How do I improve from this test?
I've printed this tuning test on my VCore 3.1 400 with a 0.6mm nozzle, in PLA at 215c through a Rapido HF/Orbiter 2, 100mm/s & 4k acceleration external perimeters. PA set to 0.045 and IS active in RRF (yeah not using Klipper but RRF on Duet 6HC). Layer height 0.2mm.
The print took roughly 1h, 40min.
I printed a Benchy with the same settings that looks pretty good, some ringing but overall better than this larger test. I understand this model was (probably) designed for a 0.4mm nozzle so the fine details will suffer.
...
overextruded solid layers with Extrudr Durapro ABS,
I am only having issues with ABS, PLA, PCTG etc work without such issues.
I am having issues with the Extrudr ABS:
solid layers get overextruded altough I did calibrate the flow rate to match the extrusion with of single perimeters exactly. ...
