Vitamin G
RRCRat Rig Community [Unofficial]
•Created by Vitamin G on 6/20/2024 in #fix-my-print
Struggling with PETG
6 replies
RRCRat Rig Community [Unofficial]
•Created by Vitamin G on 6/12/2024 in #ratos-support
Unknown command being generated on layer change since installing RatOS 2.1
7 replies
RRCRat Rig Community [Unofficial]
•Created by Vitamin G on 5/23/2024 in #fix-my-printer
Filament break between hotend and extruder when unloading filament
Hey all, I am running a rapido 2 UHF with an orbiter 2 and I consistently run into an issue when I unload filament there is always some filament that breaks off or otherwise remains in the bowden tube between the extruder and hotend. This happens almost every time I need to change filament and requires I detach the extruder to clear the block before feeding the new filament. Has anyone else ran into this issue with this hotend/extruder combo and found a solution? I should also mention I am running eva 3 with no modifications in this area.
P.S. I run the filament unload command in ratos to retract the filament.
8 replies
RRCRat Rig Community [Unofficial]
•Created by Vitamin G on 1/2/2024 in #fix-my-mesh
V-Core 3.1 400mm
27 replies
RRCRat Rig Community [Unofficial]
•Created by Vitamin G on 1/1/2024 in #ratos-support
How to change Z tilt offset for beacon probe
I got my beacon probe working finally but when I do a z tilt it is still using the offset from the inductive probe. I am not sure how to change that. Z tilt is also very slow since I changed to 5160 stepper drivers I would like to increase that speed also.
3 replies
RRCRat Rig Community [Unofficial]
•Created by Vitamin G on 12/22/2023 in #ratos-support
Difficulties with 48V stepper configuration
9 replies
RRCRat Rig Community [Unofficial]
•Created by Vitamin G on 12/17/2023 in #ratos-support
Beacon not triggering
I just wired up the beacon probe and the red LED turns on when I place a piece of metal underneath it but it still shows z probe as always being triggered. I was using the standard p&f probe before so im guessing I need to change something in the config so that klipper will use the pi port not the octopus probe port for the pin signal. Anyone have experience with this? I have attached my printer.cfg file
7 replies
RRCRat Rig Community [Unofficial]
•Created by Vitamin G on 9/16/2023 in #ratos-support
Controller and Pi fan question
I am ready to add fans for both the rpi and steppers. I only have 1 always on header left on my board. Can I use one of the pwm headers as always on? I'd like both to always be on if possible
6 replies
RRCRat Rig Community [Unofficial]
•Created by Vitamin G on 9/6/2023 in #fix-my-mesh
Solved: Mesh getting worse over time
3 replies
RRCRat Rig Community [Unofficial]
•Created by Vitamin G on 8/22/2023 in #ratos-support
Trouble connecting to mainsail on mobile
Hi all, as the title says for some reason I can almost never connect to mainsail on my phones browser. I have no issues at all connecting via any computer be it my laptop or desktop. Am I missing something to connect on my phone?
11 replies
RRCRat Rig Community [Unofficial]
•Created by Vitamin G on 8/16/2023 in #fix-my-resonance
Serious issues with belt tension/IS after installing FMMM mod
170 replies
RRCRat Rig Community [Unofficial]
•Created by Vitamin G on 8/7/2023 in #fix-my-printer
Solved: P&F inductive probe always triggered
2 replies
RRCRat Rig Community [Unofficial]
•Created by Vitamin G on 7/29/2023 in #fix-my-printer
XY motor plates not fitting well
3 replies