RainingRusty
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/18/2025 in #ratos-support
Orbiter 2.0 Current
Hi,
Just something I have seen while using the wizard. I selected "Orbiter 2" initially and had lots of extruder motor step skips. Only to realize the current was set to 0.35 Amps.
Went back to wizzard and enabled "Advanced" and see that the "LDO-36STH17" was selected. Changed it to "LDO-36STH20" but see the current does not update to 0.85A
Is this supposed to updated automatically in the wizard?
I eventually just added the correct stepper current line in my printer.cfg manually. (could have maybe also gone with lower 0.707A)
7 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/16/2025 in #ratos-support
Hotend Fan Speed
Is it possible to change the Hotend Fan Speed via command line?
I know this is not generally done but would like to reduce speed for a few seconds which doing a probe with the PZ Probe from E3D. My fan seems to cause a little disturbance from time to time when doing a mesh
12 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/13/2025 in #ratos-support
E3D PZ Probe
Built a drangon burner for my Voron V0 and used the E3D PZ Probe and EBB36.
During wizard config, used a "Geneic Probe". As it is Voron V0, I had to ad a few lines to the Printer.cfg to get a few things working for bed level and mesh.
Guess V0 was not intended to really have a probe but when I did the mesh, I could easily see I had a "Frame" issue and was able to losten the one Y rail and slighty push up while tightening again.... Problem solved.
My question is simple.... Did I miss something during the setup that I had to manually add lines to the printer.cfg, or should this just have fully worked without any changes?
Can we sometime add PZ probe to the list of probes?
4 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
In RatOS 2.1 I have uncommented the Nevermore section and added the pin.
How does the filter start and stop during a print? Is there a change in the Start G-Code I need to add?
Using Orca Slicer.
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 12/7/2024 in #ratos-support
Losing connection to MCU
9 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 11/27/2024 in #ratos-support
Internal (klipper/RatOS controlled) heater
35 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 11/6/2024 in #ratos-support
No chamber heater found
20 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 10/27/2024 in #ratos-support
Reset RatOS 2.1
Want to restart my complete setup without have to flash SD card again.
What is the easiest why to get back to defualt setup before running configuration wizard?
7 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 10/18/2024 in #fix-my-mesh
What is the secret to tightening rails?
38 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 7/1/2024 in #fix-my-print
Rough start...
81 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 4/30/2024 in #fix-my-printer
Orbiter seems to be heating TPE
2 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 4/19/2024 in #fix-my-print
Seam causing issues
5 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 4/17/2024 in #ratos-support
Enforced Heat Soak Timer
Is there a parameter somewhere that I can adjust to say wait for 2 minutes after heating the bed but before doing the leveling and bed mesh?
Would like to make sure the heat has settled throughout the bed.
4 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 1/9/2024 in #ratos-support
RatOs Update - gcode macro problem
Anyone else get this error after the last update?
Klipper reports: ERROR
Error loading template 'gcode_macro CALIBRATE_ADAPTIVE_MESH:gcode': jinja2.exceptions.TemplateSyntaxError: unexpected char '&' at 3569
123 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 1/5/2024 in #fix-my-mesh
Bed Tilt/Mesh Clarification
9 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 11/20/2023 in #fix-my-printer
Z Step
Is it required to calibrate the motor steps? My Vcore 3.1 500 seems to lose height on tall prints and eventually knocks the printed parts and so think the Z Steps might be an issue.... Or maybe not.....
This happens so much so that it breaks the "Tree supports" but snapping them in the middle. Bed adhesion is amazing.... but the force of the nozzle hitting the printed parts while traveling to next section is not good at all
10 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 11/17/2023 in #ratos-support
Chamber Heater Support
Is there any configuration/macros in RatOS supporting chamber heaters? Or do we just use standard klipper configs to add heaters and temp sensors?
7 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 11/15/2023 in #fix-my-mesh
Mesh Range High... Frame or Bed?
36 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 11/15/2023 in #ratos-support
Measure Corexy Belt Tension
6 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 11/8/2023 in #ratos-support
EBB42 - Orbiter Sensor V2.2 - RatOS Config
Can I connect the Orbiter Sensor V2.2 to the "Probe" or the "Endstop" connector on the EBB42 and then configure it in "User Override" section of printer.cfg?
3 replies