RainingRusty
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/18/2025 in #ratos-support
Orbiter 2.0 Current
Just curious, did you get to test this?
7 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/18/2025 in #ratos-support
Orbiter 2.0 Current
Note that I also run RatOS 2.0 on my other RR500 and this worked perfectly when selecting the correct motor. Hence why I was able to compare.
Just thought to mention. If my wizard or myself are "smoking" something.... then fine... Just ignore this thread and close.
7 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/18/2025 in #ratos-support
Orbiter 2.0 Current
7 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/16/2025 in #ratos-support
Hotend Fan Speed
I set the max power down and did a test and this worked, but cannot run at this low speed during the print
12 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/16/2025 in #ratos-support
Hotend Fan Speed
ok, thought so, google could not find my answer.... So had to ask
12 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/16/2025 in #ratos-support
Hotend Fan Speed
nozzle temp is in anycase only at 150 while doing the mesh
12 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/16/2025 in #ratos-support
Hotend Fan Speed
Think the resonance of the motor affects the Probing as when I dont have the fan connected, the probing works 100%
12 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/16/2025 in #ratos-support
Hotend Fan Speed
Dont was to totally switch off, but reduce speed to 50% while doing the mesh
12 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/16/2025 in #ratos-support
Hotend Fan Speed
yes
12 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/13/2025 in #ratos-support
E3D PZ Probe
4 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
Only back from business trip this week and see this topic has had a few updates. Thanks to all.
@Helge Keck , going to give both options a try and see what happens.
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
can you share what you have done
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
So you only run filter after print?
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
Interesting
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
Did you test today?
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
Did a few prints today. Nothing changed in Orca. As @Helge Keck says, starts and stops automatically based on parameters set in config file
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
Ok, For now I can just use the variable manually as needed. Thanks
43 replies
RRCRat Rig Community [Unofficial]
•Created by RainingRusty on 2/2/2025 in #ratos-support
Nevermore Filter
Had a look at this already. Might be missing something.
Just not sure what triggers the filter based on filament I am printing with
43 replies