Andrew46
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 4/3/2024 in #fix-my-print
consistent Z marks
3 replies
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 12/12/2023 in #fix-my-printer
Communication timeout during homing
17 replies
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 12/11/2023 in #fix-my-print
top surface pattern
4 replies
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 10/31/2023 in #ratos-support
pause - resume
I've been trying to get my head around the pause and resume macros within ratos.
I noticed they don't either reduce the hotend temp or turn it off during a pause.
I often have a roll runout during the night and it could sit for hours.
I've tried putting:
M109 S{params.EXTRUDER_TEMP|default(printer.extruder.target, true) }
In the resume but I can't get it back to the gcode file extruder temp. Bringing the temp down in the pause was obviously the easy part.
Is there anywhere with more information on the params and the part in brackets id like to learn more of code in detail.
8 replies
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 10/29/2023 in #ratos-support
multiple cameras
Atm im using one 1080p 60fps nozzle camera and I want to add an enclosure cam and a filliment roll cam of the same spec.
I've got 2 cameras working threw camera streamer on crowsnest but I think I'm at the limit of the Pi cpu as it will only run 2 cameras on 640p..
Has anyone any recommendations on how I can run at least 2 more @720p.
1 replies
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 10/15/2023 in #ratos-support
Webrtc camera stopped working
10 replies
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 8/15/2023 in #fix-my-printer
tmc5160 stepper issues
1 replies
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 8/3/2023 in #fix-my-printer
Stepper staying powered up
Hi lads,
So I noticed my 5160 was burning hot with the printer idle(fans off, motors supposed to be disabled), Evidently it must have killed it. I swapped to 2209's and noticed that power does not stop going to one of the motors no matter what I do.
It still works but the motor is always enabled. I have moved X to the Z3 port essentially and it doesn't have this issue. Could I have shorted or damaged a stepper port somehow?
Any way of telling if I've damaged the board? I'm just worried other areas could be too..
thanks
4 replies
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 7/17/2023 in #fix-my-printer
Rapido Clogging in enclosure
Hi All,
I have an enclosure on my second printer and it also uses a Rapido UHF. I print PETG @240 and bed at 75deg.
I'm getting constant clogs lately and can hardly get 2hrs printing. I've tried opening the door but it still clogs just lasts somewhat longer.
Will drilling the Heartbreak even help? or am I missing something?
Thanks
22 replies
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 7/15/2023 in #ratos-support
Pausing after Prime line
Tool head stops just after prime line and sits for a good few seconds. And the thing is it varys.
I've attached a video of the start of a print. Sometimes it only lasts 2 seconds but I don't see why it's not a instant traverse to part start.
5 replies
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 4/22/2023 in #fix-my-printer
Printer Shutdown TMC error?
5 replies
RRCRat Rig Community [Unofficial]
•Created by Andrew46 on 12/31/2022 in #fix-my-mesh
Before and After
1 replies