genius23pl Posts - Answer Overflow

genius23pl

•Created by genius23pl on 2/24/2025 in #fix-my-print

Wipe Line -before print - Each time the Macro worked differently, what's wrong?

Stworzylem makro [gcode_macro WIPE_LINE] description: Makro do czyszczenia dyszy przed rozpoczęciem drukowania gcode: G92 E0 G1 X2 Y2 Z4 F9000
G1 Y40 Z0.4 E16 F1000
G1 Y60 Z0.2 E14 F1000
G1 Y80.0 E14 F1200.0
G1 Y100.0 E14 F1200.0
G1 Y120.0 E14 F1200.0
G1 Y160.0 E14 F1800.0 G1 Y140.0 E14 F2300.0
G0 Z2 F15000 I'm having a problem with the WIPE_LINE macro that I'm adding in Orca Slicer. The problem is that it works differently every time - each time it prints, the purge line looks different: Once it makes only 20 mm, after which the extruder stops. Other times it makes a line up to 4 times thicker than it should be. I cannot find a rule as to why the result is different each time. Has anyone had a similar problem or have any tips on how to stabilise this?

2 replies

RRCRat Rig Community [Unofficial]

•Created by genius23pl on 1/23/2025 in #fix-my-printer

VC3.1 - SuperPinda - !! Retries aborting: Probed points range is increasing. -Z-Tilt Problem

I have been struggling for some time with a problem concerning the SuperPINDA probe which is becoming increasingly annoying. The problems mainly occur during the Z-Tilt procedure. Sometimes I have to run the print 2-3 times to get the levelling to fit within the limit of 0.012. It also happens that it is not until the 8th-9th time that the bed is leveled correctly. If the probe fails to make the correct alignment, I get the message: "Retries aborting: Probed points range is increasing." I therefore have the following questions: - Could the problem lie in the probe itself (e.g. damaged or malfunctioning)? - Is the tolerance range I have set (0.012) too small and should be increased? - What should be the correct distance between the SuperPINDA probe and the bed for optimum performance? Thank you in advance for your help

6 replies

RRCRat Rig Community [Unofficial]

•Created by genius23pl on 1/9/2025 in #fix-my-mesh

Brand new bed - flatnes problem

2 replies

RRCRat Rig Community [Unofficial]

•Created by genius23pl on 1/4/2025 in #fix-my-print

The first layer only holds on one side of the bed

13 replies

RRCRat Rig Community [Unofficial]

•Created by genius23pl on 3/25/2023 in #fix-my-printer

Printer went crazy ???

Hi. please help my printer went crazy. I replaced the Dupont plugs with XM2.54 with cable routing 1<->1 and the printer started to work wonders with the table.

2 replies

RRCRat Rig Community [Unofficial]

•Created by genius23pl on 3/9/2023 in #fix-my-print

Two type of print quality on infill

7 replies

RRCRat Rig Community [Unofficial]

•Created by genius23pl on 3/6/2023 in #fix-my-printer

Burning hotend - Rapido

9 replies

RRCRat Rig Community [Unofficial]

•Created by genius23pl on 3/4/2023 in #fix-my-printer

Z_TILT_ADJUST - Impossible to complete.

Hello. since 5 hours I can't handle both with Z_TILT_ADJUST I checked everything I know, even changed all possible motor connections to Z, Z1, Z2, LMR RML LRM pe MLR MRL in the first combination the difference goes down but around 5-6 it starts to grow??? and I got the error Retries aborting: Probed points range is increasing log in the attachment

35 replies

RRCRat Rig Community [Unofficial]

•Created by genius23pl on 3/4/2023 in #fix-my-printer

Rapido UHF can 't reach more than 226 °C