DanO Posts - Answer Overflow

DanO

Posts Comments

RRCRat Rig Community [Unofficial]

•Created by DanO on 12/26/2024 in #fix-my-printer

MCU Shutdown (only on idle) VC4

4 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 12/26/2024 in #fix-my-printer

Abysmal Flow

11 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 8/6/2024 in #fix-my-print

Strange Texture

6 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 8/6/2024 in #fix-my-mesh

Z-Tilt makes it worse

16 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 7/22/2024 in #fix-my-printer

Reassign Motor to new slot

I think the Octopus Pro 446 I have has an issue with the direction pin on the stepper_x (Motor0) slot. It only moves in one direction. If i Force move it FORCE_MOVE STEPPER=stepper_x DISTANCE=50 VELOCITY=50 It doesn't matter whether i move it + or - distance, it goes the same way. I bought new motors, bought new drivers, and swapped axis, it seems to be a board slot issue. Instead of purchasing a whole new Octopus board can I just reassign it to motor 3 slot? where X1 would normally be. Where do i reassign that variable?

8 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 5/31/2024 in #fix-my-print

poor surface on ASA and ABS

I’ve tried lowering solid infill thickness, slowing down, heating up, and everything I can think of. I haven’t put it in a dryer yet since the filament was fresh from factory. Otherwise I am a bit stumped.

13 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 5/24/2024 in #fix-my-printer

Extruder reset error only after 3+ hours of printing

15 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 3/12/2024 in #fix-my-print

weird artifact

2 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 2/11/2024 in #fix-my-printer

prints no longer start

I have been playing around with the BTT SFS V2 Filament sensor a bunch and making lots of changes in my printer.cfg Up to this point it seemed to be a weird bug that only happened occasionally while experimenting with the filament sensor gcode insertion: I print and everything is normal from heating the bed to pre-heating the hot end, and meshing. However as soon as the hot end is heating to its final printing temp the print never starts. It just hangs on heating the extruder yet the temps are reading correctly and are at temp. This is now not an occasional bug that restarting fixed but since I upgraded to 48v and 5160 steppers and the resulting changes in the printer.cfg it won’t get past the heating extruder step. Any idea where I need to look to fix the issue? It feels like I broke something with all the printer.cfg changes and has nothing to do with hardware.

8 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 1/17/2024 in #ratos-support

"Filament Unloaded" After starting print. New BTT Smart Sensor V2 - Filament Runout

I seem to have the filament runout sensor installed and working correctly. However everytime i start a print now, after the prime blob it reports "filament unloaded" and i have to hit play again. Here is my printer.cfg attached and below:

[filament_switch_sensor RUNOUT] 
switch_pin: ^PG12
pause_on_runout: True
runout_gcode:
  PAUSE # [pause_resume] is required in printer.cfg
  M117 Filament not detected
  SET_IDLE_TIMEOUT TIMEOUT=86400
  #insert_gcode:
  #M117 Filament switch inserted


[filament_motion_sensor JAM]
switch_pin: ^PG13
detection_length: 20 # accuracy of motion sensor 2.88mm 
extruder: extruder
pause_on_runout: True
runout_gcode:
  PAUSE # [pause_resume] is required in printer.cfg
  M117 Filament jam detected
  SET_IDLE_TIMEOUT TIMEOUT=86400
  #insert_gcode:
  #M117 Filament encoder inserted

[delayed_gcode DISABLEFILAMENTSENSOR] ; This will disable the SFS 1 second after klipper starts
initial_duration: 1
gcode:
    SET_FILAMENT_SENSOR SENSOR=RUNOUT ENABLE=0 ; Put your filament sensor's name after SENSOR=
    SET_FILAMENT_SENSOR SENSOR=JAM ENABLE=0 ; Put your filament sensor's name after SENSOR=

[filament_switch_sensor RUNOUT] 
switch_pin: ^PG12
pause_on_runout: True
runout_gcode:
  PAUSE # [pause_resume] is required in printer.cfg
  M117 Filament not detected
  SET_IDLE_TIMEOUT TIMEOUT=86400
  #insert_gcode:
  #M117 Filament switch inserted


[filament_motion_sensor JAM]
switch_pin: ^PG13
detection_length: 20 # accuracy of motion sensor 2.88mm 
extruder: extruder
pause_on_runout: True
runout_gcode:
  PAUSE # [pause_resume] is required in printer.cfg
  M117 Filament jam detected
  SET_IDLE_TIMEOUT TIMEOUT=86400
  #insert_gcode:
  #M117 Filament encoder inserted

[delayed_gcode DISABLEFILAMENTSENSOR] ; This will disable the SFS 1 second after klipper starts
initial_duration: 1
gcode:
    SET_FILAMENT_SENSOR SENSOR=RUNOUT ENABLE=0 ; Put your filament sensor's name after SENSOR=
    SET_FILAMENT_SENSOR SENSOR=JAM ENABLE=0 ; Put your filament sensor's name after SENSOR=

Added to Start and end macros:

    # BTT SFS Runout Sensor enable
    M117 ENABLING the Smart Filament Sensor
    SET_FILAMENT_SENSOR SENSOR=JAM ENABLE=1 
    SET_FILAMENT_SENSOR SENSOR=RUNOUT ENABLE=1

    # Disable Smart Filament Sensor
    M117 DISABLING the Smart Filament Sensor
    G92 E0
    SET_FILAMENT_SENSOR SENSOR=JAM ENABLE=0
    SET_FILAMENT_SENSOR SENSOR=RUNOUT ENABLE=0

    # BTT SFS Runout Sensor enable
    M117 ENABLING the Smart Filament Sensor
    SET_FILAMENT_SENSOR SENSOR=JAM ENABLE=1 
    SET_FILAMENT_SENSOR SENSOR=RUNOUT ENABLE=1

    # Disable Smart Filament Sensor
    M117 DISABLING the Smart Filament Sensor
    G92 E0
    SET_FILAMENT_SENSOR SENSOR=JAM ENABLE=0
    SET_FILAMENT_SENSOR SENSOR=RUNOUT ENABLE=0

5 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 11/20/2023 in #fix-my-printer

Y axis Bearing vibration

I have a 500 and am trying to diagnose and resolve the vibration patterns from the bearings on the Y axis. I have squared and verified square a million ways. But when i tighten the belts i can never get my belt tension graph exactly to match and the bearings are vibrating as i pull the gantry back and forth. If i gently push the gantry it will bind a bit as it slides where with more force that isn't noticeable. This is a video of a print that shows the effects. I tried to make a video of the bearing vibration or binding but it really isn't apparent. One note is i did have the bearings fall out when i put the linear rails together and i bought a replacement set of bearings that I added. I am not sure if that changed things. The vibration seems the same no matter whether i pull the gantry back and forth and feel on one side or the other. Both linear rails seem to do it.

35 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 10/6/2023 in #fix-my-printer

[Solved] New 500 build. immediately clogs

21 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 8/24/2023 in #fix-my-print

ASA multi part fails (singles print fine)

27 replies

Gaming

Programming