Yathani
RRCRat Rig Community [Unofficial]
•Created by Salty Saul🧂 on 11/2/2024 in #fix-my-print
VCore4 500 hybrid 2nd layer major over extrusion
You probably need to increase the temp not reduce it. What you see here is most likely the core of the filament is still not 100% melted and not sticking to the previous layer. Even if the print finished without issue at this temp, it will look matt and will break easily
30 replies
RRCRat Rig Community [Unofficial]
•Created by Salty Saul🧂 on 11/2/2024 in #fix-my-print
VCore4 500 hybrid 2nd layer major over extrusion
This is not over extrusion but quite the opposite. 36 flow might be too high for your setup specially when printing at 210c. Have you done flow rate test to find your max?
30 replies
RRCRat Rig Community [Unofficial]
•Created by Christian - cbTechnology on 10/3/2024 in #fix-my-print
Blobs on Perimeters
If i might suggest, try to lower the retraction speed to 60mm and increase the print temp. Your print color looks matt it might require more heat
11 replies
RRCRat Rig Community [Unofficial]
•Created by Christian - cbTechnology on 10/3/2024 in #fix-my-print
Blobs on Perimeters
Retraction speed is too high .. for Orbiter it should be at 120mm/s max. Sometimes even a lower retraction speed of 50-30 would give a better result
11 replies
RRCRat Rig Community [Unofficial]
•Created by TonyStyles on 9/28/2024 in #fix-my-print
Issue with dimensional accuracy on the z axis
I know for ABS/ASA we compensate for shrinkage by increasing of 2%. I would assume its the same thing for Nylon not sure though. Usually shrinkage happens on X and Y but yours printer vertical. Other thing is to check for skew, you might had skew issue before moving to 2.1
8 replies
RRCRat Rig Community [Unofficial]
•Created by TonyStyles on 9/28/2024 in #fix-my-print
Issue with dimensional accuracy on the z axis
Could it be part shrinkage? 2% is within that range
8 replies
RRCRat Rig Community [Unofficial]
•Created by Yathani on 9/27/2024 in #ratos-support
Orbiter Smart Filament Sensor Action Button
Thank you for your reply .. all the configurations was already there but linked instead of inserted in the printer.cfg. I add the mark "!" in front of the switch pin and it worked! I though its only needed to reverse the direction of the motor.. Many thanks 👍
6 replies
RRCRat Rig Community [Unofficial]
•Created by Yathani on 8/13/2024 in #ratos-support
Ratos 2.1 + Adaptive mesh + and Orcaslicer
I tried Prusa Slicer where i have copied all of my settings from OrcaSlicer and the printer behaved normal. Even Adaptive mesh worked! So i think it's more of configuration issue on OrcaSlicer rather than Ratos issue
4 replies
RRCRat Rig Community [Unofficial]
•Created by Yathani on 8/13/2024 in #ratos-support
Ratos 2.1 + Adaptive mesh + and Orcaslicer
4 replies
RRCRat Rig Community [Unofficial]
•Created by Yathani on 7/31/2024 in #ratos-support
Failed to detect NetworkManager Service
Then likely it got changed when i reinstalled klipper screen which prompt me to install Network Manager at the end. I clicked Yes thinking it will fix the issue but apeparently not
68 replies
RRCRat Rig Community [Unofficial]
•Created by Yathani on 7/31/2024 in #ratos-support
Failed to detect NetworkManager Service
My Pi started a wifi with Ratos and when I tried to join the network to configure my home network, it says incorrect password for "raspberry". I think i will just reinstalled Ratos again at this point and I hope this issue won't come back again from klipper screen.
68 replies
RRCRat Rig Community [Unofficial]
•Created by Yathani on 7/31/2024 in #ratos-support
Failed to detect NetworkManager Service
I was able to initially access SSH through [email protected] but then i reinstalled klipper screen and now even rato.local does not work 😅
68 replies
RRCRat Rig Community [Unofficial]
•Created by Yathani on 7/18/2024 in #ratos-support
Last RatOS.cfg issue
thank you 🙂
12 replies
RRCRat Rig Community [Unofficial]
•Created by Yathani on 7/18/2024 in #ratos-support
Last RatOS.cfg issue
You are correct .. I picked the wrong one 😅
12 replies
RRCRat Rig Community [Unofficial]
•Created by Yathani on 7/18/2024 in #ratos-support
Last RatOS.cfg issue
12 replies
RRCRat Rig Community [Unofficial]
•Created by lainbh on 7/6/2024 in #fix-my-print
Issue with ABS printing
Reduce the bed temp to around 90c and turn your fan up a little higher until you find the sweet spot. The print look worst closer to the bed because it can't cool the layers as good
6 replies
RRCRat Rig Community [Unofficial]
•Created by hhes on 7/9/2024 in #fix-my-print
[VC4 400] Pattern on the wall
Try to print cylinder in vase mode .. This should help you to see if you have z banding or it's extrusion/PA tuning related
16 replies
RRCRat Rig Community [Unofficial]
•Created by chicken on 6/28/2024 in #fix-my-printer
VC4 * 500 Gantry warping issues as printer heats
Thanks .. I will look into the gantry twist
108 replies
RRCRat Rig Community [Unofficial]
•Created by chicken on 6/28/2024 in #fix-my-printer
VC4 * 500 Gantry warping issues as printer heats
[bed_mesh] horizontal_move_z: 5 mesh_min: 20,20 mesh_max:390,390 probe_count: 21,21 fade_start: 1.0 fade_end: 10.0 mesh_pps: 2,2 algorithm: bicubic bicubic_tension: 0.1 [beacon] serial: /dev/beacon x_offset: 0 y_offset: 18.2 mesh_main_direction: x mesh_runs: 1 speed: 15. lift_speed: 80. contact_max_hotend_temperature: 275 [z_tilt] z_positions: 0,0 200,400 400,0 points: 60,60 200,370 360,60 retry_tolerance: 0.005
108 replies
RRCRat Rig Community [Unofficial]
•Created by chicken on 6/28/2024 in #fix-my-printer
VC4 * 500 Gantry warping issues as printer heats
I also reduced the tolerance of the Z adjustment to 0.005. It takes the printer 4-5 tries to get it but eventually it does better than that
108 replies