Kyle59 Comments - Answer Overflow

Kyle59

•Created by Kyle59 on 4/14/2025 in #ratos-support

BTT Octopus DFU not detected

That is my option now. Unfortunately, I have to disconnect everything to do it - but I do have labels on all the wires at least from when I built it

3 replies

RRCRat Rig Community [Unofficial]

•Created by Kyle59 on 4/13/2025 in #ratos-support

Raspberri Pi issue?

I seem to be able to connect to the Pi over ethernet, but not over wireless now for some reason. I was updating everything else to the latest version. Klipper kept giving an error "TEST_RESONANCES" not found. After updating everything else I started to setup in RatOS, selected the right printer and mainboard setup (Octopus V1.1) and it wanted to flash that, so followed that procedure and once I got to DFU Mode and hit the reset button, it starts to flash and then says DFU Mode not found. A little bit frustrated at the moment with it, so giving it a break for a little while before coming back tomorrow to go back over it

13 replies

RRCRat Rig Community [Unofficial]

•Created by Kyle59 on 4/13/2025 in #ratos-support

Raspberri Pi issue?

Ah, managed to get the right image and loaded it up. At the moment though, I can only connect via ethernet. Wireless was up on the pi and gave the correct password - stupid quiestion, how to get back in tot he Pi to make sure I didn't mis-type the p/w? On ethernet, I have now updated everything, but I have an error on Klipper "Existing Command "TEST_RESONANCES" not found in RATOS Override Anyone seen and corrected htis at all?

13 replies

RRCRat Rig Community [Unofficial]

•Created by Kyle59 on 4/13/2025 in #ratos-support

Raspberri Pi issue?

Ok, ok. Oops. I’ll go back over it all when I get home. I thought that was the pi image….

13 replies

RRCRat Rig Community [Unofficial]

•Created by Kyle59 on 4/13/2025 in #ratos-support

Raspberri Pi issue?

First I tried RatOS 2.0.2, downloading 2023-06-09-RatOS-2.0.2-armbian-CB1.img.xz but when that didn't work, I then tried the same with 2.1.0, downloading 2024-07-27-RatOS-2.1.0-RC2-armbian-CB1.img.xz Used Balena Etcher to put the image on to the MicroSD card in each instance

13 replies

RRCRat Rig Community [Unofficial]

•Created by Kyle59 on 6/30/2023 in #fix-my-print

Possible under-extrusion on infill

Ok, no problem

14 replies

RRCRat Rig Community [Unofficial]

•Created by Kyle59 on 6/30/2023 in #fix-my-print

Possible under-extrusion on infill

Printer profile or filament profile?

14 replies

RRCRat Rig Community [Unofficial]

•Created by Kyle59 on 6/30/2023 in #fix-my-print

Possible under-extrusion on infill

Cool. If you have issues, get back to me. Going to orca was a real good move as far as I was concerned. Happy to share my files etc if you’re on messenger

14 replies

RRCRat Rig Community [Unofficial]

•Created by Kyle59 on 6/30/2023 in #fix-my-print

Possible under-extrusion on infill

Yes, at the time I was using Simplify3D, and I had the wrong one of either relative or absolute extrusion ticked in the settings. Changing to the other setting fixed that issue for me. That said, I have since changed to Orca Slicer and have had much better success at printing with that slicer

14 replies

RRCRat Rig Community [Unofficial]

•Created by Kyle59 on 4/5/2024 in #fix-my-resonance

Vcore 400 graphs

It's all good everyone. I've had to go back to square one on it and start again on the belts. Havng a bit of a closer look, the X axis gantry was not running parallel for me as well, and worked on rectifying that. It was caused by too much tension on one of the belts, so loosened that and found that I cut it a bit short, so have ordered a new one to replace it - rookie error that I should not have made. Will get the new belt Wednesday and put it all together properly and see how it goes then....

3 replies

RRCRat Rig Community [Unofficial]

•Created by GhostHands on 3/11/2024 in #fix-my-printer

Layer shifts

The graphs showed the x and y very close, then tensioned one up a bit more and one of htem collapses completely, anyone else every have the same thing?

6 replies

RRCRat Rig Community [Unofficial]

•Created by GhostHands on 3/11/2024 in #fix-my-printer

Layer shifts

Mine has just started doing the same thing. Did a x/y belt tension in Ratos and was horrible, so went through the process and got it all fixed up. Noticed some of the bearings sounded like they were running with gravel in them, so pulled down and lubricated, which helped there a lot. I am going to get a new seat of bearings in and replace all of them. Re-set the belts again and tensioned all nicely. The next print went beautifully for 2hrs, and then the layers shifted horribly again on it. Going to pull the belts apart completely and check it all, but most likely retire them and replace them along with the bearings. There is something very wring with it. Pretty sure it can only be belt or bearings......

6 replies

RRCRat Rig Community [Unofficial]

•Created by Kyle59 on 6/30/2023 in #fix-my-print

Possible under-extrusion on infill