Steef Comments - Answer Overflow

Steef

Posts Comments

RRCRat Rig Community [Unofficial]

•Created by Steef on 12/8/2024 in #ratos-support

RatOS Slicer configuration - conflicting advice in documentation

@blacksmithforlife 🇺🇸 thanks for reminding me that I'm running 2.1 RC-3. D'oh. Answered.

5 replies

RRCRat Rig Community [Unofficial]

•Created by SYG|Krizalid87 on 11/8/2024 in #fix-my-mesh

VC 3.1 400 Fix back corner

8 replies

RRCRat Rig Community [Unofficial]

•Created by popoblito on 11/16/2024 in #fix-my-printer

Is my V3.1 300 making too many Z adjustments?

if it still requires multiple runs, maybe some bolt is loose. If not, it's just because you moved the PEI sheet. Perhaps some small particles between the sheet and the magnetic base

6 replies

RRCRat Rig Community [Unofficial]

•Created by popoblito on 11/16/2024 in #fix-my-printer

Is my V3.1 300 making too many Z adjustments?

Try doing z-tilt, shut down the machine, restart the machine, do the same homing & Z-tilt again without removing the PEI sheet inbetween.

6 replies

RRCRat Rig Community [Unofficial]

•Created by popoblito on 11/16/2024 in #fix-my-printer

Is my V3.1 300 making too many Z adjustments?

However, removing and re-placing the PEI sheet will easily cause a deviation above that tolerance. I would say this is normal

6 replies

RRCRat Rig Community [Unofficial]

•Created by popoblito on 11/16/2024 in #fix-my-printer

Is my V3.1 300 making too many Z adjustments?

Typically it does it once but doesn't require correction, incidentally it will do it twice.

6 replies

RRCRat Rig Community [Unofficial]

•Created by SYG|Krizalid87 on 11/8/2024 in #fix-my-mesh

VC 3.1 400 Fix back corner

8 replies

RRCRat Rig Community [Unofficial]

•Created by SYG|Krizalid87 on 11/8/2024 in #fix-my-mesh

VC 3.1 400 Fix back corner

I also think the back corner is difficult to fix with the frame, as the electronics panel doesn't allow easy moving of those corners. Personally, I just put strips of thin tape between the magnetic sticker and the steel flex plate. It lets you correct small areas quite easily.

8 replies

RRCRat Rig Community [Unofficial]

•Created by DJDupid on 7/13/2024 in #ratos-support

Where is RatOS 2.1?!!!!!

#letsgooooo

75 replies

RRCRat Rig Community [Unofficial]

•Created by mavi - ilezirabbit on 5/24/2024 in #fix-my-mesh

my mesh is bad...

Did you run Z-Tilt before making this mesh? If not, please do and re-peat the mesh

3 replies

RRCRat Rig Community [Unofficial]

•Created by Tornillo on 5/30/2024 in #fix-my-mesh

Fix my fucked up mesh

If not, please do so and make a new mesh

3 replies

RRCRat Rig Community [Unofficial]

•Created by Tornillo on 5/30/2024 in #fix-my-mesh

Fix my fucked up mesh

Did you run Z-Tilt before making this mesh?

3 replies

RRCRat Rig Community [Unofficial]

•Created by spoown on 6/7/2024 in #ratos-support