Achi447
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 4/6/2024 in #german-support
Octopus Pro 446 kann nicht geflasht werden
Ich probiere gerade mein Board zu flashen, aber es will irgendwie nicht. Ich habe die Jumper wie in der RatOs Dokumentation gesetzt und kontrolliert. Bei den Steppern habe ich 4 auf 48V gestellt und 4 auf 24V. In der http://ratoslocal/configure?step=1 waehle Ich das Octopus Pro 446 gehe auf next, dann auf flash firmware manually, dann auf compile, dann auf download, dann verschiebe ich die firmware.bin auf meine sd karte und mache sie dann in das Mainboard. Dann gehe Ich auf actions und auf flash all connected mcus nach ungefaehr 30 Sekunden steht da flash failed und nach ungefair einer Minute stuerzt die Seite ab und die Seite wird weiss und Ich kann auch nicht wieder Rauf dasselbe passiert auch wenn Ich auf check board status drücke. Wenn Ich dann das USB-C kabel nicht aus dem PI mache kann Ich auch nicht wieder rauf. Keine Ahnung was los ist.
81 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 4/6/2024 in #ratos-support
Beeping sound when turning on Octopus Pro 446 while trying to flash it
So im trying to flash my Octopus Pro446 i only have Power for the board and usb c to pi plugged in. as soon as i trun it on the board starts beeping and nothing happens. i set the stepper jumpers to 48v and 24v and i have not connected anything to the stepper terminal power wise. i use a 32gb sd card.
31 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 3/30/2024 in #german-support
Hybrid core xy Software Fragen
Software Fragen
21 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 3/1/2024 in #fix-my-resonance
Weird Belt Tension graph
3 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 2/26/2024 in #german-support
Komische Artefakte auf den außen Wänden
8 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 2/23/2024 in #fix-my-print
Weird Pattern on flat Walls
6 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 12/22/2023 in #german-support
Druck Dimensionierung passt nicht
9 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 12/16/2023 in #fix-my-printer
Skew Correction Issue
I got two parts that are the same. one is cnc machined and the other 3d printed. The 3d Printed one doesn't align with the cnc one. I suspect a skew issue I tried to set it up in RatOs, but it only improves a bit. Am i supposed to do it multiple times ? I did the Klipper method. If that helps. Or could it also be something else ike speed, acce settings or belt tension?
27 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 11/17/2023 in #fix-my-printer
AWD Stepper Motor problem
35 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 11/13/2023 in #german-support
Euclid Probe funktioniert nicht richtig
(Menschliches Versagen)
64 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 11/12/2023 in #ratos-support
"Shutdown due to expected probe state to be deployed but is stowed" Euclid
Im not sure what's wrong but i cant get my euclid Probe to work. I cant even get it to trigger manually when i press it.
19 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 11/12/2023 in #fix-my-printer
Sensor less Homing not properly working
Im trying to setup sensor less homing for my v400, but for homeing X it moves to the right and sometimes it doesnt even hit anything and it just stops. for y it moves to the back, but it also sometimes doesn't hit anything. i tried sensitivity from 1 to 200 but that didn't change anything.
8 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 9/20/2023 in #fix-my-print
Z-Banding V Minion
39 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 9/17/2023 in #fix-my-print
ASA overhang problems
7 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 9/9/2023 in #german-support
Komische layer lines
20 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 9/5/2023 in #fix-my-resonance
Y-Axis problems
9 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 9/3/2023 in #fix-my-print
weird layers
58 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 8/30/2023 in #fix-my-printer
rapido uhf(old) Heater not heating properly
26 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 7/23/2023 in #german-support
Jemand eine Idee was das Problem sein könnte?
31 replies
RRCRat Rig Community [Unofficial]
•Created by Achi447 on 7/23/2023 in #fix-my-print
Weird patern on the corners
4 replies