Shades
RRCRat Rig Community [Unofficial]
•Created by Shades on 10/29/2024 in #fix-my-printer
VAOC LED ring not working
@Mr_Phelps_VCore_4.0_500 on the LED board where the cable connector is look on the opposite side of where the cable plugs in and find the 3 legs, I used those to test, admittedly I have really thin probes on my multimeter. But if you can read 4.95v there you know it's making it all the way to the LED board and rule out any issues with the LED connector cable.
28 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 10/29/2024 in #fix-my-printer
VAOC LED ring not working
Mine turned out to be a bad board. I verified by grabbing a multimeter and verifying I had 4.95v all the way to the LED board.
28 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 10/29/2024 in #fix-my-printer
VAOC LED ring not working
I haven't tried the actual VAOC homing routine yet, but shouldn't the flashlight icon on the VAOC screen trigger the LEDs
28 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 10/29/2024 in #fix-my-printer
VAOC LED ring not working
I did have to sand it down as per the guide to make it fit in the housing
28 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 10/29/2024 in #fix-my-printer
VAOC LED ring not working
No I misspoke earlier
28 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 10/29/2024 in #fix-my-printer
VAOC LED ring not working
28 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 10/29/2024 in #fix-my-printer
VAOC LED ring not working
sorry yes red is the right most let me open it up
28 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 10/29/2024 in #fix-my-printer
VAOC LED ring not working
on that photo red would be the left most pin
28 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 10/29/2024 in #fix-my-printer
VAOC LED ring not working
28 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 10/29/2024 in #fix-my-printer
VAOC LED ring not working
Here you go
28 replies
RRCRat Rig Community [Unofficial]
•Created by Kano on 10/21/2024 in #fix-my-printer
New machine vcore 4 machine with idex installed before commissioning
Had this issue as well, this note should be added to the commissioning guide, as it emphasizes not running the Y belts during commissioning.
10 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 8/28/2024 in #ratos-support
RatOS 2.1.0-RC2 Reporting that it cant write to stepper_x's Globalregister.
@chicken that was it thanks!
7 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 8/28/2024 in #ratos-support
RatOS 2.1.0-RC2 Reporting that it cant write to stepper_x's Globalregister.
@chicken so I followed the guide which had you pull the jumpers to put them into uart if they should be in SPI then that should be an easy fix and I'll give it a go
7 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 12/3/2022 in #fix-my-mesh
V-Minion Bed Mesh question
16 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 12/3/2022 in #fix-my-mesh
V-Minion Bed Mesh question
Not going to lie it took a while to get there
16 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 12/3/2022 in #fix-my-mesh
V-Minion Bed Mesh question
Also made sure to heat the hotend to 150 before each mesh
16 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 12/3/2022 in #fix-my-mesh
V-Minion Bed Mesh question
Based off that mesh I tightened to screws to adjust and redid the mesh and then adjusted again <- did this about 12x until it was at the .09 number stated above
16 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 12/3/2022 in #fix-my-mesh
V-Minion Bed Mesh question
Then I took a level to it and made sure the bed was level then I leveled the x gantry to the bed and ran a mesh
16 replies
RRCRat Rig Community [Unofficial]
•Created by Shades on 12/3/2022 in #fix-my-mesh
V-Minion Bed Mesh question
So I started with new nylon washers and got the bed finger tight.
16 replies
RRCRat Rig Community [Unofficial]
•Created by Johnjrk on 12/7/2022 in #fix-my-print
Printing with ASA on V-Minion
I completely forgot to mention I had no luck with it until I realized the extruder was slipping on the filament and not extruding the right amount despite tuning the e-steps. Everything started to work a lot better once I popped it on to 2 clicks (the flexables setting on the lgx lite).
12 replies