Naiofz91 Comments - Answer Overflow

Naiofz91

•Created by Naiofz91 on 9/6/2023 in #fix-my-printer

ADXL app. correlation

actually turns out i have a different version of the adxl, this is a mpu 6050, and it required different install proccess was for me as a noob user is kindda overwhilming, so i just went n got the adxl345, did the solder work n all n got it working.

7 replies

RRCRat Rig Community [Unofficial]

•Created by Naiofz91 on 9/12/2023 in #fix-my-resonance

Error trying to activate ADXL setting on klipper.

turns out u cant uncomment tha # before 500 mm printer, so silly, yet vauge. i should'nt have wait 24 hours to just figure out something so ridiculoues...

5 replies

RRCRat Rig Community [Unofficial]

•Created by Naiofz91 on 9/12/2023 in #fix-my-resonance

Error trying to activate ADXL setting on klipper.

doesnt fix it.

5 replies

RRCRat Rig Community [Unofficial]

•Created by Naiofz91 on 9/2/2023 in #fix-my-printer

" Endstop z still triggered after retract "

9 replies

RRCRat Rig Community [Unofficial]

•Created by Naiofz91 on 9/2/2023 in #fix-my-printer

" Endstop z still triggered after retract "

had to change it to a bl touch, my super pinda was probably faulty,, u can find one on prusa 's website for around 25$ " superpinda "

9 replies

RRCRat Rig Community [Unofficial]

•Created by Naiofz91 on 9/6/2023 in #fix-my-printer

ADXL app. correlation

Also X and Y direction looks to be inverted if i was to place it as per the eva mount with or that doesnt matter ?

7 replies

RRCRat Rig Community [Unofficial]

•Created by Naiofz91 on 9/5/2023 in #fix-my-printer

connecting 4 pin controller fan

that's part cooling fan, what i need is explanation for the Controller fan..

4 replies

RRCRat Rig Community [Unofficial]

•Created by Naiofz91 on 9/2/2023 in #fix-my-printer

" Endstop z still triggered after retract "

when it throws the error, is when trying to home Z with the default setting, and then when checking the probe statues it says triggered for both Z and probe, so the fact that the probe statues changing makes me doubt that the probe is bad, unless it just suddenly shorted somehow and isnt actually triggering...

9 replies

RRCRat Rig Community [Unofficial]

•Created by Naiofz91 on 9/2/2023 in #fix-my-printer

" Endstop z still triggered after retract "

the Z offset adjustment of -1.4 was an attempt to put back the same z from my previous set up, the issue occured from before i edieted fro 0.0. regarding wiring, i checked connectivity with a multi-meter for and it returned connected between all 3 different wires, i visually checked the cripms and port and it was ok.. what makes me wounder is that it was working fine before i did the upgrade. and when i convert pin with " ! " and checked stautes of end stops it showed open for both z and probe, but doesnt trigger when it should. while on the os default, it immiditly retracts the bed down and shws the error message.

9 replies

RRCRat Rig Community [Unofficial]

•Created by wolfie on 5/5/2023 in #fix-my-print

X-Y Hole compensation / tolerances

crucial inquiry, and i belive for a user whos expecting reliable values plays a big role. thanks for putting it outhere.

4 replies

RRCRat Rig Community [Unofficial]

•Created by VisualTech48 on 4/30/2023 in #fix-my-mesh

Bed mesh fix results

even though you'd be risking big prints coming off of the bed, which damages integrity of the product in terms of reliability when 0.2 may not seem much as a number but in terms on nozzle output that's an entire layer line difference or even more if you're printing with finer quality.

32 replies

RRCRat Rig Community [Unofficial]

•Created by Naiofz91 on 2/18/2023 in #fix-my-print

underextrusion upon 1'st print test cube.

Worked like a charm, thanks guys.

5 replies

RRCRat Rig Community [Unofficial]

•Created by Naiofz91 on 2/18/2023 in #fix-my-print

underextrusion upon 1'st print test cube.