Ross13 Posts - Answer Overflow

Ross13

Posts Comments

RRCRat Rig Community [Unofficial]

•Created by Ross13 on 11/29/2024 in #fix-my-printer

VAOC Camera Not Working

3 replies

RRCRat Rig Community [Unofficial]

•Created by Ross13 on 11/26/2024 in #ratos-support

VC4 IDEX Belay in Copy/Mirror Mode

I have the Annex Belay system set up for T0 & T1. This works without issue when printing in single toolhead mode, and whichever toolhead is active the belay system is also active for that toolhead. However, when trying to use copy/mirror mode, the belay only works for T0. The T1 on toolhead extruder works as normal, but the belay extruder for T1 does not move. Going back to single mode and both belay systems for T0 and T1 work appropriately again. Here is my config:

[belay t0_belay]
extruder_type: extruder_stepper
extruder_stepper_name: stepper_t0
sensor_pin: ^PF4
multiplier_high: 1.05
multiplier_low: 0.95
debug_level: 0

[tmc2209 extruder_stepper stepper_t0]
uart_pin: PG8 #CS Pin on Octopus Max Diagram
stealthchop_threshold: 0
interpolate: False
run_current: 0.707
sense_resistor: 0.11
driver_TBL: 0
driver_TOFF: 4
driver_HEND: 6
driver_HSTRT: 7
driver_SGTHRS: 40

[extruder_stepper stepper_t0]
extruder: extruder
#   The extruder this stepper is synchronized to. If this is set to an
#   empty string then the stepper will not be synchronized to an
#   extruder. This parameter must be provided.
step_pin: PA8
dir_pin: !PC7
enable_pin: !PC9
microsteps: 64
full_steps_per_rotation: 200
rotation_distance: 4.63

[belay t1_belay]
extruder_type: extruder_stepper
extruder_stepper_name: stepper_t1
sensor_pin: ^PF3
multiplier_high: 1.05
multiplier_low: 0.95
debug_level: 0

[tmc2209 extruder_stepper stepper_t1]
uart_pin: PD6 #CS Pin on Octopus Max Diagram
stealthchop_threshold: 0
interpolate: False
run_current: 0.707
sense_resistor: 0.11
driver_TBL: 0
driver_TOFF: 4
driver_HEND: 6
driver_HSTRT: 7
driver_SGTHRS: 40

[extruder_stepper stepper_t1]
extruder: extruder1
#   The extruder this stepper is synchronized to. If this is set to an
#   empty string then the stepper will not be synchronized to an
#   extruder. This parameter must be provided.
step_pin: PA10
dir_pin: !PA9
enable_pin: !PA15
microsteps: 64
full_steps_per_rotation: 200
rotation_distance: 4.63

[belay t0_belay]
extruder_type: extruder_stepper
extruder_stepper_name: stepper_t0
sensor_pin: ^PF4
multiplier_high: 1.05
multiplier_low: 0.95
debug_level: 0

[tmc2209 extruder_stepper stepper_t0]
uart_pin: PG8 #CS Pin on Octopus Max Diagram
stealthchop_threshold: 0
interpolate: False
run_current: 0.707
sense_resistor: 0.11
driver_TBL: 0
driver_TOFF: 4
driver_HEND: 6
driver_HSTRT: 7
driver_SGTHRS: 40

[extruder_stepper stepper_t0]
extruder: extruder
#   The extruder this stepper is synchronized to. If this is set to an
#   empty string then the stepper will not be synchronized to an
#   extruder. This parameter must be provided.
step_pin: PA8
dir_pin: !PC7
enable_pin: !PC9
microsteps: 64
full_steps_per_rotation: 200
rotation_distance: 4.63

[belay t1_belay]
extruder_type: extruder_stepper
extruder_stepper_name: stepper_t1
sensor_pin: ^PF3
multiplier_high: 1.05
multiplier_low: 0.95
debug_level: 0

[tmc2209 extruder_stepper stepper_t1]
uart_pin: PD6 #CS Pin on Octopus Max Diagram
stealthchop_threshold: 0
interpolate: False
run_current: 0.707
sense_resistor: 0.11
driver_TBL: 0
driver_TOFF: 4
driver_HEND: 6
driver_HSTRT: 7
driver_SGTHRS: 40

[extruder_stepper stepper_t1]
extruder: extruder1
#   The extruder this stepper is synchronized to. If this is set to an
#   empty string then the stepper will not be synchronized to an
#   extruder. This parameter must be provided.
step_pin: PA10
dir_pin: !PA9
enable_pin: !PA15
microsteps: 64
full_steps_per_rotation: 200
rotation_distance: 4.63

2 replies

RRCRat Rig Community [Unofficial]

•Created by Ross13 on 11/26/2024 in #fix-my-resonance

VC4 500mm IDEX

7 replies

RRCRat Rig Community [Unofficial]

•Created by Ross13 on 11/21/2024 in #ratos-support

Upgrading From Hybrid To IDEX 2x T0 but no T1 in Setup Wizard

13 replies

RRCRat Rig Community [Unofficial]

•Created by Ross13 on 11/1/2024 in #fix-my-printer

Dual Extruder Set Up Issues

I'm trying to run two orbiter extruders inline with Belay to prevent filament feeding issues on my 500mm VC4. The second extruder pulling off the spool does not move at all and I cannot find what I did wrong (the extruder does work when plugged into the toolhead, so it's not a mechanical failure). I'm using the following config, and after several hours of searching cannot figure out what I did wrong. I've tried using the SYNC_EXTRUDER_MOTION EXTRUDER=my_extra_extruder MOTION_QUEUE=extruder but only ever get the error The value 'my_extra_extruder' is not valid for EXTRUDER Please help, I've spent hours on this and I know it shouldn't be that hard to get working

[belay my_belay]
extruder_type: extruder_stepper
extruder_stepper_name: my_extra_stepper
sensor_pin: ^PF4
multiplier_high: 1.05
multiplier_low: 0.95
debug_level: 1

[tmc2209 extruder_stepper my_extra_stepper]
uart_pin: PG8 #CS Pin on Octopus Max Diagram
stealthchop_threshold: 0
interpolate: False
run_current: 0.707
sense_resistor: 0.11
driver_TBL: 0
driver_TOFF: 4
driver_HEND: 6
driver_HSTRT: 7
driver_SGTHRS: 40

[extruder_stepper my_extra_stepper]
extruder: extruder
#   The extruder this stepper is synchronized to. If this is set to an
#   empty string then the stepper will not be synchronized to an
#   extruder. This parameter must be provided.
step_pin: PA8
dir_pin: PC7
enable_pin: PC9
microsteps: 64
full_steps_per_rotation: 200
rotation_distance: 4.63

[belay my_belay]
extruder_type: extruder_stepper
extruder_stepper_name: my_extra_stepper
sensor_pin: ^PF4
multiplier_high: 1.05
multiplier_low: 0.95
debug_level: 1

[tmc2209 extruder_stepper my_extra_stepper]
uart_pin: PG8 #CS Pin on Octopus Max Diagram
stealthchop_threshold: 0
interpolate: False
run_current: 0.707
sense_resistor: 0.11
driver_TBL: 0
driver_TOFF: 4
driver_HEND: 6
driver_HSTRT: 7
driver_SGTHRS: 40

[extruder_stepper my_extra_stepper]
extruder: extruder
#   The extruder this stepper is synchronized to. If this is set to an
#   empty string then the stepper will not be synchronized to an
#   extruder. This parameter must be provided.
step_pin: PA8
dir_pin: PC7
enable_pin: PC9
microsteps: 64
full_steps_per_rotation: 200
rotation_distance: 4.63

6 replies

RRCRat Rig Community [Unofficial]

•Created by Ross13 on 7/6/2024 in #fix-my-resonance

VC4 500mm Hybrid Belt Tensioning Trouble Shooting

16 replies

RRCRat Rig Community [Unofficial]

•Created by Ross13 on 11/30/2023 in #fix-my-printer

SuperPINDA (z probe) Always Triggered

23 replies

Gaming

Programming