Ross13
RRCRat Rig Community [Unofficial]
•Created by WrinklySackNick on 12/23/2024 in #fix-my-resonance
Y accel wont go above 2000 - vcore 3.1 with toolhead
X is pretty much unaffected from previous input shapers
11 replies
RRCRat Rig Community [Unofficial]
•Created by WrinklySackNick on 12/23/2024 in #fix-my-resonance
Y accel wont go above 2000 - vcore 3.1 with toolhead
Also getting a near identical graph on my VC4 500mm (running in just CoreXY right now). Prominent peak at ~100hz that tapers near identically to yours. I don't have the peak between 150-175hz, but otherwise very similar
11 replies
RRCRat Rig Community [Unofficial]
•Created by Ross13 on 11/29/2024 in #fix-my-printer
VAOC Camera Not Working
Bumping to see if anyone has any last ideas before I warranty the camera
3 replies
RRCRat Rig Community [Unofficial]
•Created by Ross13 on 11/21/2024 in #ratos-support
Upgrading From Hybrid To IDEX 2x T0 but no T1 in Setup Wizard
That would make sense. It was after PID tuning and hitting the SAVE_CONFIG that I first noticed the problem
13 replies
RRCRat Rig Community [Unofficial]
•Created by Ross13 on 11/21/2024 in #ratos-support
Upgrading From Hybrid To IDEX 2x T0 but no T1 in Setup Wizard
I've deleted the backups at this point :/
13 replies
RRCRat Rig Community [Unofficial]
•Created by Ross13 on 11/21/2024 in #ratos-support
Upgrading From Hybrid To IDEX 2x T0 but no T1 in Setup Wizard
hmm, not sure what happened then. I don't know it all, but I know enough to not mess with that section
13 replies
RRCRat Rig Community [Unofficial]
•Created by Ross13 on 11/21/2024 in #ratos-support
Upgrading From Hybrid To IDEX 2x T0 but no T1 in Setup Wizard
Also, while upgrading from Hybrid to IDEX, I ended up with two of the "SAVE_CONFIG - DO NOT EDIT" Sections in my printer.cfg
It kept the old Save Config from the Hybrid, which was the top "SAVE_CONFIG" section. The bottom one was the new one for the IDEX. I deleted the hybrid one.
13 replies
RRCRat Rig Community [Unofficial]
•Created by Ross13 on 11/21/2024 in #ratos-support
Upgrading From Hybrid To IDEX 2x T0 but no T1 in Setup Wizard
dyocis gave me the answer. Need to restart fresh to get it to work. In the printer selection tab, I clicked on IDEX, then back on Hybrid and it gave me a prompt asking if I wanted to start fresh. Clicked on that, then clicked on IDEX again and got the same prompt, which I again clicked "start fresh." Everything is working appropriately now
13 replies
RRCRat Rig Community [Unofficial]
•Created by Ross13 on 11/1/2024 in #fix-my-printer
Dual Extruder Set Up Issues
So the above config is golden
6 replies
RRCRat Rig Community [Unofficial]
•Created by Ross13 on 11/1/2024 in #fix-my-printer
Dual Extruder Set Up Issues
Dead stepper motor driver 🙃 It was a brand new one, so didn't think to swap it out until this morning
6 replies
RRCRat Rig Community [Unofficial]
•Created by NastyStew on 7/25/2024 in #fix-my-printer
No Beacon model loaded
Link to 2.1 download: https://github.com/Rat-OS/RatOS/releases/tag/v2.1.0-RC1
20 replies
RRCRat Rig Community [Unofficial]
•Created by NastyStew on 7/25/2024 in #fix-my-printer
No Beacon model loaded
on 2.1, follow the above linked instructions (do not use the plain BEACON_CALIBRATE command - that is for RatOS 2.0 or vanilla klipper)
20 replies
RRCRat Rig Community [Unofficial]
•Created by NastyStew on 7/25/2024 in #fix-my-printer
No Beacon model loaded
But 2.1 is waaay better than 2.0 because it has beacon contact
20 replies
RRCRat Rig Community [Unofficial]
•Created by NastyStew on 7/25/2024 in #fix-my-printer
No Beacon model loaded
You can home X and Y (but not Z) and run BEACON_CALIBRATE
20 replies
RRCRat Rig Community [Unofficial]
•Created by NastyStew on 7/25/2024 in #fix-my-printer
No Beacon model loaded
Are you on RatOS 2.0 or 2.1? Regardless, you need to run the beacon calibrate command. What command are you using to do the beacon calibrate?
20 replies
RRCRat Rig Community [Unofficial]
•Created by NastyStew on 7/25/2024 in #fix-my-printer
No Beacon model loaded
Did you run the beacon calibration yet?
20 replies
RRCRat Rig Community [Unofficial]
•Created by Ross13 on 7/6/2024 in #fix-my-resonance
VC4 500mm Hybrid Belt Tensioning Trouble Shooting
I need to get back to tuning it again, but haven't. Been a bit busy using the printer
16 replies
RRCRat Rig Community [Unofficial]
•Created by Ross13 on 7/6/2024 in #fix-my-resonance
VC4 500mm Hybrid Belt Tensioning Trouble Shooting
Yeah has been with filament in it
16 replies
RRCRat Rig Community [Unofficial]
•Created by mystefix. on 7/14/2024 in #fix-my-resonance
are the shaper graphs fine ? V-Core 3.1 300m with RR Toolhead Beta 2
Yes, those are fine
Belt graph isn't perfect but they are close (two identifiable peaks in the correct locations, belts are somewhat close to each other in tension). May be worth looking into your toolhead and seeing if any wires are flopping around and could be ziptied down (since you seem to have a second peak around 100Hz, which is usually toolhead caused). It's nothing major given that your input shaper graphs are looking good.
Use MZV for both X and Y. It is probably recommending ZV in X because your vibration % is low in the grand scheme of things, even if MZV does offer a lower vibration percent. ZV sucks in actual use those, so stick with MZV and the recommended acceleration in MZV for your outside perimeters
4 replies
RRCRat Rig Community [Unofficial]
•Created by DJDupid on 7/13/2024 in #ratos-support
Where is RatOS 2.1?!!!!!
Docs for 2.1 are forthcoming, but once you've got the printer set up there isn't much you need them for
75 replies