kakapo
RRCRat Rig Community [Unofficial]
•Created by kakapo on 11/21/2024 in #fix-my-print
inconsistent layer stacking
13 replies
RRCRat Rig Community [Unofficial]
•Created by kakapo on 4/1/2024 in #ratos-support
how to slow down probing routine/movement
i like the custom prime blob a lot, as well as adaptive meshing, but the movement in between probing points it just too aggressive to my liking. i dont mind if i takes a minute or two more during this sequence since it will still be insignificant compared to the print time. however, i am unable to disect the various config files and find the relevant parameter. any pointers?
7 replies
RRCRat Rig Community [Unofficial]
•Created by kakapo on 3/14/2024 in #fix-my-print
polygons instead of circles n(mechanical issue)
9 replies
RRCRat Rig Community [Unofficial]
•Created by kakapo on 1/29/2024 in #ratos-support
4028 starts blowing after ~1h of inactivity/standby
i am running a sanyo on an SKrat with the dedicated 4 wire connection and the standard configs. i think the follwing happens but i want to be sure: i think after an hour of inactivity the printer goes into standby and the fan will blow at 100% because of safety reasons. I wanted to double check since the OS page states similiar "mal"function can fry the your board.
thanks in advance for any insights
8 replies
RRCRat Rig Community [Unofficial]
•Created by kakapo on 1/17/2024 in #ratos-support
configure other ip's than 192.168.50.1?
is this possible an how can i approach it? since ill be running multiple ratrig printers and i would prefer to give them static ip's
3 replies
RRCRat Rig Community [Unofficial]
•Created by kakapo on 1/7/2024 in #ratos-support
purge line/poop placement will not update after overriding probe offsets
i cannot find the files inside RatOS that specifiec this placement. right now it poops besides the printbed.. it works but not as good as it used to. Maybe it is also due to setting up sensorless homing? could be..
12 replies
RRCRat Rig Community [Unofficial]
•Created by kakapo on 1/3/2024 in #ratos-support
couple of questions regarding customization
so far the installation was very smooth! a lot smoother than my experience with vanilla klipper, so a big thank you to the devs. most stuff is intuitive; however i would like to customize the UI and setup leds with klipped led effect
-can i edit the ratrig logo on the UI? tried the normal way and via Winscp, first didnt work second could find the files
-does ratOS support plugins as octoeverywhere and klipper led effect?
-the power consumption is also charted which makes the graph look messy; can it somehow be hidden?
37 replies
RRCRat Rig Community [Unofficial]
•Created by kakapo on 11/30/2023 in #ratos-support
i backed up my printer.cfg, but not the files it referances to (lgx.cfg etc) can i find those somewh
soo... the usb port of my octopus broke of, and after 2 days research i got it working over uart. no mcu error anymore and also the temps show correctly (i frankensteined a printer.cfg).
now i am really hesitant to start messing with the config since i might blow up somehing. safest would be to download the cfg's my config references to. (i bought the printer second hand so i dont know all the parts and pints etc.)
also... i installed fresh mainsail, no ratos. could get it working with UART.
13 replies
RRCRat Rig Community [Unofficial]
•Created by kakapo on 9/12/2023 in #ratos-support
cant upload my wifi credentials via the ratos hotspot..
is there any other way to do this? SSHing into the pi did not work as well. im trying to run the printer in a ethernetless spot
38 replies