O_Pinguim Comments - Answer Overflow

Nope, not yet. It sounded like they're were going to cut a new release of RC4 in the next few days, so I may just wait for that. Or limp along with an un-updated version of RC2.

21 replies

RRCRat Rig Community [Unofficial]

•Created by O_Pinguim on 1/1/2025 in #ratos-support

Configurator 502 Bad Gateway on RatOS 2.1.x

21 replies

RRCRat Rig Community [Unofficial]

•Created by O_Pinguim on 1/31/2024 in #fix-my-print

Stringing and blobbing with a 0.6 mm nozzle

Thanks for the suggestion, @truckdoor ! I gave it a try and didn't notice much difference, unfortunately. I tried switching to my other nozzle, too, and that didn't seem to help. I did see some difference bumping my PA up to like 0.2, but If I go much higher the extruder starts skipping. I guess I'll have to switch back to a 0.4 mm nozzle until I have time to play more with this.

13 replies

RRCRat Rig Community [Unofficial]

•Created by O_Pinguim on 1/31/2024 in #fix-my-print

Stringing and blobbing with a 0.6 mm nozzle

13 replies

RRCRat Rig Community [Unofficial]

•Created by O_Pinguim on 10/29/2023 in #fix-my-print

Switched to 0.6mm nozzle, rough time of calibration

I did change the nozzle diameter to 0.6 in the printer config and in Prusa Slicer. My default extrusion width is 0.62mm, perimeters are at 0.69mm. I've been playing with retraction settings and I've set them super low (0.5mm retraction at 55mm/s retract and 20mm/s deretract). I've tried extrusion multipliers between 0.92 and 0.96. I'm using a pretty high-quality filament and I did do a temperature calibration at 205 deg C. I can see some change to the yellow problem and green problem when I change the extrusion multipliers, but the yellow problem never completely goes away and the green problem starts to become overextrusion. Red is always there.

2 replies

RRCRat Rig Community [Unofficial]

•Created by Ducky on 10/27/2023 in #fix-my-print

Inconsistent First Layers vcore 3.1 w .6mm nozzle

I'd be interested in hearing how you fix these problems- I, too, just switched to a 0.6 mm nozzle and I'm getting gaps in the perimeter on the z-seam corner and some gaps between the infill and the perimeter. I've tried a wide variety of Pressure Advance settings, but I'm not seeing much change. Hopefully you find the winning combination!

9 replies

RRCRat Rig Community [Unofficial]

•Created by O_Pinguim on 9/17/2023 in #fix-my-mesh

Pretty flat, but tilted on initial meshes (V-Core 3.1 400mm)

I ran the z tilt first, then the homing, and then the bed mesh.

8 replies

RRCRat Rig Community [Unofficial]

•Created by O_Pinguim on 10/3/2023 in #fix-my-print

Extrusion differences (thickness) and rippling

2 replies

RRCRat Rig Community [Unofficial]

•Created by O_Pinguim on 9/27/2023 in #fix-my-printer

No skew correction option for printer.cfg?

Thanks!

4 replies

RRCRat Rig Community [Unofficial]

•Created by O_Pinguim on 9/21/2023 in #fix-my-printer

Filament doesn't fit through Rapido heat break

Thanks, all! I contacted Ratrig and they're going to refund the cost of the Rapido. I've ordered a replacement that should get here soon (fingers crossed!).

5 replies

RRCRat Rig Community [Unofficial]

•Created by O_Pinguim on 9/17/2023 in #fix-my-mesh

Pretty flat, but tilted on initial meshes (V-Core 3.1 400mm)

Thanks for your help!

8 replies

RRCRat Rig Community [Unofficial]

•Created by O_Pinguim on 9/17/2023 in #fix-my-mesh

Pretty flat, but tilted on initial meshes (V-Core 3.1 400mm)

I have it down to 0.133. Is that good? Good enough?

8 replies

RRCRat Rig Community [Unofficial]

•Created by O_Pinguim on 9/17/2023 in #fix-my-mesh

Pretty flat, but tilted on initial meshes (V-Core 3.1 400mm)

8 replies

Gaming

Programming