phongshader Comments - Answer Overflow

phongshader

Posts Comments

RRCRat Rig Community [Unofficial]

•Created by phongshader on 11/1/2024 in #fix-my-mesh

vcore 3.1 500

nope, still on 2

9 replies

RRCRat Rig Community [Unofficial]

•Created by phongshader on 11/1/2024 in #fix-my-mesh

vcore 3.1 500

After trying to print a large print where the 1st layer appearance is important, it looks like bed mesh compensation is not working. One corner is squished/too thin , the upper middle is barely adhering to the bed the lower middle is squished, and so on. How do I check to see if there is any compensation happening? I'm using the ratos defaults, the only change I've made to bed_mesh is speed and I'm using adaptive_bed_mesh

variable_adaptive_mesh: True

[bed_mesh]
speed: 1000

variable_adaptive_mesh: True

[bed_mesh]
speed: 1000

9 replies

RRCRat Rig Community [Unofficial]

•Created by phongshader on 11/1/2024 in #fix-my-mesh

vcore 3.1 500

ooohh, RATOS 2.1, where do I get that?

9 replies

RRCRat Rig Community [Unofficial]

•Created by phongshader on 11/1/2024 in #fix-my-mesh

vcore 3.1 500

9 replies

RRCRat Rig Community [Unofficial]

•Created by phongshader on 10/17/2024 in #ratos-support

unable to ssh in now!?!

reinstalled 😕

7 replies

RRCRat Rig Community [Unofficial]

•Created by phongshader on 10/17/2024 in #ratos-support

unable to ssh in now!?!

to be clear I can access Mainsail with the IP address but I cannot ssh in to the pi because it appears that my password is incorrect, but I also cannot login to the pi locally as well...I never changed the password for the account. Looks like I may need to save all my data and reprovision the os, unless there is a better solution here

7 replies

RRCRat Rig Community [Unofficial]

•Created by phongshader on 10/17/2024 in #ratos-support

unable to ssh in now!?!

7 replies

RRCRat Rig Community [Unofficial]

•Created by phongshader on 2/11/2024 in #fix-my-printer

orbiter filament sensor setup?

more testing...I've tested the orbiter supplied macro and it works as expected however it is not triggered by the runout switch. To test the switches functionality I set it up as an endstop , on PB4 pin of the ebb36, and klipper/mainsail read the switch as closed when closed and open when open. How can I test what a pin is receiving other than what I've done? I've tried pins PB4 and PB5 on the ebb36 board with the same result. For some reason, as a runout sensor, klipper is not getting input from the switch but klipper is getting input as a endstop🤷

5 replies

RRCRat Rig Community [Unofficial]

•Created by phongshader on 2/11/2024 in #fix-my-printer

orbiter filament sensor setup?

tried switching pins to PB5 and PB7, no difference, keeps printing after filament has runout

5 replies

RRCRat Rig Community [Unofficial]

•Created by phongshader on 12/17/2023 in #fix-my-printer

homing x axis homes y axis and visa versa

this got me sorted out, everything is moving in the right direction now. Thank you all for the help and guidance!

9 replies

RRCRat Rig Community [Unofficial]

•Created by phongshader on 12/17/2023 in #fix-my-printer

homing x axis homes y axis and visa versa

I did check and tried reversing the plugs...did not fix it

9 replies

RRCRat Rig Community [Unofficial]

•Created by phongshader on 10/19/2023 in #ratos-support