phongshader
RRCRat Rig Community [Unofficial]
•Created by phongshader on 11/1/2024 in #fix-my-mesh
vcore 3.1 500
9 replies
RRCRat Rig Community [Unofficial]
•Created by phongshader on 10/17/2024 in #ratos-support
unable to ssh in now!?!
I recently moved my printer to a different room in the house. I can access on web/mainsail but am unable to ssh into the pi. RatOS v2.0.2-36-g230929e3, klipper v0.12.0-229-g589bd64c, mainsail v2.12.0,
Distro: RatOS v 2.0.2 (bullseye)...any idea why I'm all of the sudden unable to ssh in on Windows or Mac.
Access denied I've changed nothing on the pi and have been ssh in for over a year...any suggestions on how to fix this?7 replies
RRCRat Rig Community [Unofficial]
•Created by phongshader on 2/11/2024 in #fix-my-printer
orbiter filament sensor setup?
I have an orbiter v2 with filament sensor connected to an ebb36. The runout button is connected to pin PB4, unload button to pin PB3 and those pins are a part of the I2C socket pins. The unload button functions as expected but the runout button does not. The print continues to run after the filament has runout and the sensor led has turned red on the sensor signifying a runout. I also get a console message "Printing! Can't unload filament right now!" which made me think the buttons were reversed because I should only get that message when the unload button is pressed. I double checked the wiring and it is as documented. I also wired each button as an endstop to test functionality and they worked and were read by klipper. Any suggestions on what to look for settings changes?
5 replies
RRCRat Rig Community [Unofficial]
•Created by phongshader on 12/21/2023 in #fix-my-printer
controller fan not shutting down
My controller fan is not stopping after the time specified, 120 sec, The only way to stop the fan is to reset the firmware or restart the printer. I have a 2nd controller fan that I've set the overrides on and it continues to run after 120sec as well. It is triggered by the activation of the X stepper motor...although what is the X stepper on a corexy? Any suggestions on what to change/look for to get the fans to shut down after 120sec of no movement? Hmmm, what starts the timer for fan shutdown? Is it the stepper not moving for a set amount of time or is it something else?
10 replies
RRCRat Rig Community [Unofficial]
•Created by phongshader on 12/17/2023 in #fix-my-printer
homing x axis homes y axis and visa versa
I just got my vcore 3.1 500 assembled and tried to home...ran into a bunch of problems, motors moving in the opposite direction than expected, that was easy to sort out. Where I'm at now is homing x axis moves the y axis and of course it fails because the x endstop is never triggered and this is true for y homing as well. I double checked the belt routing and it is consistent with the Dozuki build guide, https://ratrig.dozuki.com/Guide/05.+CoreXY+Motor+Assemblies/138?lang=en, double checked to make sure I have the steppers plugged into the right sockets on the octopus pro board consistent with the ratos wiring guide, https://os.ratrig.com/docs/boards/btt/octopus-pro-446/
9 replies
RRCRat Rig Community [Unofficial]
•Created by phongshader on 10/19/2023 in #ratos-support
I know RatOS doesn't want me to use a can bus....
I know RatOS doesn't want me to use a can bus but I'm using a can bus....I did a fresh ratos install, added an rs485 can hat to the pi and did the setup ....can0 shows up as down and I can't get it to come up. I double...triple checked all the things and still not active, but listed as down. I did a vanilla Mainsail OS install and did the things I needed to install the rs485 can hat (the same procedures as on RatOs) and can0 is up and functioning. This is a long explanation for the question, is there something in the current RatOs that keeps a can interface from functioning?
12 replies
RRCRat Rig Community [Unofficial]
•Created by phongshader on 7/4/2023 in #fix-my-resonance
what should I be aiming for for belt tension?
6 replies
RRCRat Rig Community [Unofficial]
•Created by phongshader on 6/19/2023 in #fix-my-printer
odd z wobble
2 replies