WrinklySackNick Comments - Answer Overflow

WrinklySackNick

•Created by WrinklySackNick on 1/5/2025 in #fix-my-print

Underextrusion?

It might have been filament shreds in the orbiter? It was the only thing I didn't check and the issue seems to have resolved itself randomly without changing anything in the software.

10 replies

RRCRat Rig Community [Unofficial]

•Created by WrinklySackNick on 1/5/2025 in #fix-my-print

Underextrusion?

I should clarify, PA values 0, 0.01, 0.02, 0.03, 0.04, 0.05, 0.06, 0.07, 0.08, 0.09, 0.1 did not have a noticable effect on the testing cubes. It was set to 0.02 last week when it was working great

10 replies

RRCRat Rig Community [Unofficial]

•Created by WrinklySackNick on 1/5/2025 in #fix-my-print

Underextrusion?

outer walls printed 100mm/s 5k accel, top/bottoms printed 50mm/s 5k accel. polymaker galaxy red asa

10 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 12/26/2024 in #fix-my-printer

Abysmal Flow

https://west3d.com/products/phaetus-rapido-2-heat-block-replacement-for-rapido-2-hot-ends

17 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 12/26/2024 in #fix-my-printer

Abysmal Flow

I haven't seen just the tube but you can get the block with tube

17 replies

RRCRat Rig Community [Unofficial]

•Created by WrinklySackNick on 12/23/2024 in #fix-my-resonance

Y accel wont go above 2000 - vcore 3.1 with toolhead

I'm running the newest RatOS with the newest input shaping routine. It seems that the frequency it picks is good, I just ignored the max accel it gives me.

11 replies

RRCRat Rig Community [Unofficial]

•Created by WrinklySackNick on 12/23/2024 in #fix-my-resonance

Y accel wont go above 2000 - vcore 3.1 with toolhead

Weirdly while it says y accel above 2k is not recommended the machine is still whisper quiet at 300mm 10k accel (leftmost print) and no real issues. Maybe it is a software thing. (On the right is 100mm, 3k accel, no input shaping) I guess I don't really have a problem

11 replies

RRCRat Rig Community [Unofficial]

•Created by WrinklySackNick on 12/23/2024 in #fix-my-resonance

Y accel wont go above 2000 - vcore 3.1 with toolhead

11 replies

RRCRat Rig Community [Unofficial]

•Created by WrinklySackNick on 12/23/2024 in #fix-my-resonance

Y accel wont go above 2000 - vcore 3.1 with toolhead

I used the new gates belt. I did leave a lot of wiggle room on the belts, I'll try removing a notch or two at a time

11 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 12/26/2024 in #fix-my-printer

Abysmal Flow

https://www.youtube.com/watch?v=8vf_gY5Qg2o

17 replies

RRCRat Rig Community [Unofficial]

•Created by DanO on 12/26/2024 in #fix-my-printer

Abysmal Flow

am i correct in assuming everything is the same as the old set up except the new extruder? My first guess is usually sometimes people forget to screw the new nozzle in while it is hot, it can mess up flow. Or if you dissasemble and reassemble the hotend/heatbreak sometimes people crush the pipe. Third guess is sometimes you can get an orbiter extruder where the filament path on the gears is not perfectly aligned.

17 replies

RRCRat Rig Community [Unofficial]