loganluckless
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/30/2024 in #ratos-support
Reverse pin logic question
I'm trying to run an rgb nozzle light off the endstop port of the ebb36. I'm having trouble figuring out where to put the !. I would think it would be toolboard_t0:!PB6 but that returns an error. Any help would be greatly appreciated!
14 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 7/4/2023 in #ratos-support
Beacon leadscrew safe_home_x
Hi, I'm trying to figure out how to set my safe_home_x position to a couple mm off center so my beacon probe doesn't hit my z leadscrew. I'm using the beacon recommended code but that doesn't seem to change where the default bounce back position is.
[safe_z_home]
home_xy_position: 107.5, 90 # update for your machine
z_hop: 3
I'm going to chop a couple mm off the top of my screw next week but until then is there something obvious I'm missing?
11 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/27/2023 in #fix-my-print
Bad bed leveling
1 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/10/2023 in #fix-my-printer
Strange heating behavior
2 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 1/9/2023 in #fix-my-printer
weirdo extruder issue
Today my extruder randomly started jamming when my printer occupies the back third or so of the build area. Everything worked fine this morning but out of nowhere this happens. I don't know how many more wacko problems it is possible to run into in a single build.
If anyone has any ideas or solutions I would appreciate it. Tomorrow I'll swap the motor driver but beyond that I'm at a loss.
2 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 1/5/2023 in #fix-my-print
Belt tension and jerk questions
Hello,
I have a vcore 3.1 400mm enclosed printing mostly ABS. My belt tension is clearly too low but I'm not sure what values I should be tensioning too. Does anyone have a well working reference for the corexy belt measurement I should shoot for?
Additionally my pressure advance is clearly too low but when I run a tuning tower (or any print for that matter) my jerk will occasionally jump up to 10mm/s. Didn't see any settings for this in super slicer but I'm probably missing something. Any help on either question would be much appreciated, thanks.
2 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 12/18/2022 in #ratos-support
Restart forced after prime blob
Midway through a print my printer haulted and seemed to do a firmware restart, gcode fans stopped, unable to connect to the web interface exc. Now whenever I start a print it gets to the prime blob and then haults. I reverted back to my earlier config, updated everything and checked my wiring with nothing unusual happening. Attached is my klipper log and a download of my gcode file. I'm inexperienced with klipper but I don't see anything unusual. No error is thrown it just restarts.
My heaters still work, all my endstops, probes and sensors work fine and motion seems to be working perfectly fine. I have no idea what would be going on. My setup is mostly unmodified with a btt octopus pro f446 and a raspberry pi 4b powered off the rgb header of the board.
47 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 12/16/2022 in #ratos-support
Configuration override confusion
7 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 12/16/2022 in #ratos-support
hotend cooling fan limiter
Hi, for those experienced I'm sure this is a stupid easy problem but I'm having trouble setting my hotend fan speed to be something other than 100% when the hotend is on. I did something like this in rrf but I can't find the option in ratos.
3 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 12/14/2022 in #ratos-support
motor uart not connecting
7 replies