loganluckless
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/30/2024 in #ratos-support
Reverse pin logic question
Alright I'll post over there thanks!
14 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/30/2024 in #ratos-support
Reverse pin logic question
That's with the ! Removed completely
14 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/30/2024 in #ratos-support
Reverse pin logic question
IDK that's how I've always run neo pixels off end stop ports. I'm getting sporadic flashing colors mid print but otherwise no response to a change in color
14 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/30/2024 in #ratos-support
Reverse pin logic question
14 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/30/2024 in #ratos-support
Reverse pin logic question
14 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
For anyone this helps I figured out the issue. After replacing a bunch of the heaters and swapping the PSU out with a UHP 350 with no improvement I stopped powering the pi over gpio from my SKRat and switched to a btt sksm. No more issues with 50+ hours on the V0 in the last week. I ended up having this issue on my vcore 400 as well and the fix was the same. Not sure why this happened all of the sudden but at least the fix is easy and cheap
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
I run it at trade shows on my table it's a great attention grabber
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
Totally agree. I may try and cram a uhp 200 in there. I love the v0 for what I use it for but I have some design issues with it
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
I have a manta m5p I could swap in somewhat easy but I kinda doubt that'll solve anything
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
It's a meanwell lrs150. This was a Facebook marketplace purchase of an ldo 0.1 that I upgraded to a 0.2. I found some wiring issues with the original owners setup so I would say there's a good chance it had a rough life
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
It also doesn't do it at idle as far as I've seen so many it's just a bad psu
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
IDK I don't think so even if everything was full power at once I don't think it would overwhelm the PSU. What's weird is I can heat up to 110 on the bed and 280 on the nozzle at the same time with no issues. It's strange that it takes so much time to have an issue. Maybe I'll try putting a fan on the PSU it does get a little tosty
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
That's what I was thinking. The power supply is the only constant between the 2 boards
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
I'll check it all, is there anything I should look out for?
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
That was the first disconnect since reinstalling ratos 2.1.0 I may be able to swap back and get a log from my 2.0.2 install
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
That's just the error I screenshoted it's 50/50 between the toolboard and the MCU
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
The tophat is closer than I like to the umbilical setup. Maybe that would cause it? Could a strain relief issue on the toolboard cause the SKRat to disconnect?
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 6/2/2024 in #ratos-support
Intermittent connectivity issue with both MCUs
strange that it persists across different rpis and sd cards though. I have been using a SanDisk a1 sd card those are generally pretty hardy
39 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 7/4/2023 in #ratos-support
Beacon leadscrew safe_home_x
Thanks, that should fix it until I can trim down that leadscrew. I haven't hit the beacon yet and hopefully that'll never happen. Unfortunately I'm running 5160s and I hear sensorless is not great if it works at all on them.
11 replies
RRCRat Rig Community [Unofficial]
•Created by loganluckless on 7/4/2023 in #ratos-support
Beacon leadscrew safe_home_x
I have done that but even with the maximum adjustment of the y end stop the beacon still hits the leadscrew. The default behavior has the x axis home then go to center of the bed. When the y axis then homes it hits the screw. Is there a way to change that bounce back behavior?
11 replies