MONSOONO
RRCRat Rig Community [Unofficial]
•Created by MONSOONO on 7/30/2024 in #fix-my-printer
4028 Tripping 12V Rail
Yeah, I'm going to bench it tonight. Sadness all around.
8 replies
RRCRat Rig Community [Unofficial]
•Created by MONSOONO on 7/30/2024 in #fix-my-printer
4028 Tripping 12V Rail
Thank you for your help
8 replies
RRCRat Rig Community [Unofficial]
•Created by MONSOONO on 7/30/2024 in #fix-my-printer
4028 Tripping 12V Rail
I just checked the board and it is ouputting at 15V on the 12V rail. Do you think this would describe the failure mode?
8 replies
RRCRat Rig Community [Unofficial]
•Created by MONSOONO on 7/13/2024 in #ratos-support
RatOS Manta CB1 - Repeated "Timer too close" Failures
I don't have much to add, just to state that I am happy to provide whatever information might be helpful. I am inclined to think it is the CB1.
14 replies
RRCRat Rig Community [Unofficial]
•Created by JaminCollins on 5/1/2024 in #fix-my-printer
Beacon revH - bed mesh hangs klipper/mainsail
Writing this for posterity: Had the same error, just had to do a bed tilt adjustment before probing
11 replies
RRCRat Rig Community [Unofficial]
•Created by elliott on 5/28/2024 in #ratos-support
RatOS - All Repos show as Corrupt
I'm excited to try the new stuff.
29 replies
RRCRat Rig Community [Unofficial]
•Created by elliott on 5/28/2024 in #ratos-support
RatOS - All Repos show as Corrupt
Much appreciated. Looks like it ran successfully.
29 replies
RRCRat Rig Community [Unofficial]
•Created by elliott on 5/28/2024 in #ratos-support
RatOS - All Repos show as Corrupt
Thank you very much for the help. Everything seems to be working though. Configurator, etc. How can I confirm whether or not it is necessary to go further? Will "sudo ~/printer_data/config/RatOS/scripts/ratos-update.sh" erase or affect the things that are set up correctly?
29 replies
RRCRat Rig Community [Unofficial]
•Created by elliott on 5/28/2024 in #ratos-support
RatOS - All Repos show as Corrupt
29 replies
RRCRat Rig Community [Unofficial]
•Created by elliott on 5/28/2024 in #ratos-support
RatOS - All Repos show as Corrupt
Everything seems to be running. Is there another step that is required now? I didn't run any install scripts to begin with.
29 replies
RRCRat Rig Community [Unofficial]
•Created by elliott on 5/28/2024 in #ratos-support
RatOS - All Repos show as Corrupt
The "Hard Recovery" option appears to have worked, and successfully updated to "v2.1.0-RC1-117-gba010121".
29 replies
RRCRat Rig Community [Unofficial]
•Created by elliott on 5/28/2024 in #ratos-support
RatOS - All Repos show as Corrupt
I also experienced a similar issue. I fresh installed 2.1 on the CB1. Initially, many components showed as corrupt. A few refreshes and restarts gradually removed the corrupt marker from most components.
The exception is the RatOS item, which is still marked as corrupt. Pings to github work fine.
29 replies
RRCRat Rig Community [Unofficial]
•Created by MONSOONO on 6/11/2024 in #ratos-support
RatOS 2.1 on CB1 Wireless Setup Issue
Much appreciated
6 replies
RRCRat Rig Community [Unofficial]
•Created by MONSOONO on 6/11/2024 in #ratos-support
RatOS 2.1 on CB1 Wireless Setup Issue
I'll take the L on this one. It does say it right above where I was reading :(. A little bit of an issue remains, is that the hotspot disappears very fast. It's a bit of a speedrun to punch in the wifi info before it vanishes
6 replies
RRCRat Rig Community [Unofficial]
•Created by Troy der Große on 3/25/2024 in #fix-my-resonance
Cant find the issue between 75 and 140 HZ
What have you tried?
2 replies
RRCRat Rig Community [Unofficial]
•Created by MONSOONO on 4/26/2024 in #fix-my-print
Terrible ABS Bridges on Orca Slicer
I will test in the morning
14 replies
RRCRat Rig Community [Unofficial]
•Created by MONSOONO on 4/26/2024 in #fix-my-print
Terrible ABS Bridges on Orca Slicer
disabling scarf seams removed the seam placement on the bridges
14 replies
RRCRat Rig Community [Unofficial]
•Created by MONSOONO on 4/26/2024 in #fix-my-print
Terrible ABS Bridges on Orca Slicer
Perhaps it's these seams on the bridge. I'm not sure why orca is doing this.
14 replies
RRCRat Rig Community [Unofficial]
•Created by MONSOONO on 4/26/2024 in #fix-my-print
Terrible ABS Bridges on Orca Slicer
14 replies
RRCRat Rig Community [Unofficial]
•Created by MONSOONO on 4/26/2024 in #fix-my-print
Terrible ABS Bridges on Orca Slicer
Here are the results from the slicer analysis
ORCA/PS
layer height .45/.45
width .45/.5?
flow variable.5?/.5-.8
layer time 32.5/29
fan speed 35/55
14 replies