Kyreus
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
interesting, didn't know that
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
i wouldn't say that 1e3 is always binding - I had that too while not having the right belt tension
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
I had the same issue, the wheel on the tensioning arm is rattling af - put some filament in it, just far enough, that this wheel touches the filament -> problem solved
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
with filament in it?
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
yeah not the best situation for tuning is graphs xD
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
interestingly I left my y belts because I couldn't get them to a good value and tried fixing my bowed bed - at the end of the day my y results were on 7k and mvz - sadly I tried to turn my gantry and now I had to start over again :KEKW:
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
never looked at the graphs for 300 printers to be honest - from my 500 perspective this would be a dream :KEKW:
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Sgt. Waffles on 11/6/2024 in #fix-my-mesh
VC4 400 hybrid bowed along Y axis, trending down in X axis
Did you get it better? Facing the same issue hoping for someone to find a solution since nothing I do changes the bow
4 replies
RRCRat Rig Community [Unofficial]
•Created by Anrot on 10/16/2024 in #fix-my-resonance
VC4 Idex Belts
I hate you for your y graphs :madge:
but your x graph will settle once you have it at the right tension
1158 replies
RRCRat Rig Community [Unofficial]
•Created by Kyreus on 11/7/2024 in #fix-my-mesh
VC4 500 Comissioning mesh
25 replies
RRCRat Rig Community [Unofficial]
•Created by Kyreus on 11/7/2024 in #fix-my-mesh
VC4 500 Comissioning mesh
For me it looks like it's a bed issue tbh
25 replies
RRCRat Rig Community [Unofficial]
•Created by Kyreus on 11/7/2024 in #fix-my-mesh
VC4 500 Comissioning mesh
25 replies
RRCRat Rig Community [Unofficial]
•Created by Kyreus on 11/7/2024 in #fix-my-mesh
VC4 500 Comissioning mesh
do you still think it's the gantry? I've turned the extrusion by 90 degrees same result
25 replies
RRCRat Rig Community [Unofficial]
•Created by Kyreus on 11/7/2024 in #fix-my-mesh
VC4 500 Comissioning mesh
25 replies
RRCRat Rig Community [Unofficial]
•Created by Kyreus on 11/7/2024 in #fix-my-mesh
VC4 500 Comissioning mesh
yeah I always run z tilt before meshing
25 replies
RRCRat Rig Community [Unofficial]
•Created by Kyreus on 11/7/2024 in #fix-my-mesh
VC4 500 Comissioning mesh
seems to not get better with rescrewing it
25 replies
RRCRat Rig Community [Unofficial]
•Created by Kyreus on 11/7/2024 in #fix-my-mesh
VC4 500 Comissioning mesh
25 replies
RRCRat Rig Community [Unofficial]
•Created by Kyreus on 11/7/2024 in #fix-my-mesh
VC4 500 Comissioning mesh
What nm amount? Then I'll try that
25 replies
RRCRat Rig Community [Unofficial]
•Created by Kyreus on 11/7/2024 in #fix-my-mesh
VC4 500 Comissioning mesh
Yes, i started from the left and went to the right - I can unscrew it one more time and screw them back in just in case - give me a few minutes
25 replies
RRCRat Rig Community [Unofficial]
•Created by Kyreus on 11/7/2024 in #fix-my-mesh
VC4 500 Comissioning mesh
it definitely got better, but I'm already pulling up very hard and this is the best it gets
25 replies