ctbjdm_04135 Comments - Answer Overflow

ctbjdm_04135

Posts Comments

RRCRat Rig Community [Unofficial]

•Created by anddelbel on 1/21/2025 in #ratos-support

MCU 'Toolboard t0' shutdown: Timer too close.

Yeah I was referring to the molex connector, black and red wires

51 replies

RRCRat Rig Community [Unofficial]

•Created by anddelbel on 1/21/2025 in #ratos-support

MCU 'Toolboard t0' shutdown: Timer too close.

I had that error when the power feed to the toolboard was loose (umbilical feeding power to the ebb42). Check the pins, make sure they are solid and the connector is good. My connector was loose, ended up adding a drop of CA glue and that solved it.

51 replies

RRCRat Rig Community [Unofficial]

•Created by anddelbel on 1/21/2025 in #ratos-support

MCU 'Toolboard t0' shutdown: Timer too close.

Have you considered it may be overheating? Add active cooling on the pi?

51 replies

RRCRat Rig Community [Unofficial]

•Created by Backyarder on 12/11/2024 in #fix-my-printer

cannot connect to pi ip.

then immediately update it once it's installed

56 replies

RRCRat Rig Community [Unofficial]

•Created by Backyarder on 12/11/2024 in #fix-my-printer

cannot connect to pi ip.

under assets

56 replies

RRCRat Rig Community [Unofficial]

•Created by Backyarder on 12/11/2024 in #fix-my-printer

cannot connect to pi ip.

It's the first in the list there.

56 replies

RRCRat Rig Community [Unofficial]

•Created by Backyarder on 12/11/2024 in #fix-my-printer

cannot connect to pi ip.

https://github.com/Rat-Os/RatOS/releases - you presumably want 2.1.0-RC2

56 replies

RRCRat Rig Community [Unofficial]

•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support

Unable to write tmc spi 'stepper_z' register GLOBALSCALER

I’m using the Octopus Max EZ. It has a bunch of ports. I didn’t have the stepper motor cables plugged in to the ports that matches the drivers. I.e. there are like 8 ports (from memory) and I had offset the cable plug from a stepper driver by 1

428 replies

RRCRat Rig Community [Unofficial]

•Created by ctbjdm_04135 on 11/14/2024 in #fix-my-mesh

Wavy Vcore 4 500 mesh!

thanks!!!! will try that!

5 replies

RRCRat Rig Community [Unofficial]

•Created by ctbjdm_04135 on 11/8/2024 in #ratos-support

Unable to write tmc spi 'stepper_z' register GLOBALSCALER

Thank you! Confirmed I fixed this - had a mismatch of driver slot install and motor cable port. SMH, this has been killing me.

428 replies

RRCRat Rig Community [Unofficial]

•Created by mabaul on 10/28/2024 in #ratos-support

Getting IDEX to work

I can't directly help you, but saw this other day, same error: https://discord.com/channels/582187371529764864/1300179219606802522/1300199670257291294

14 replies

RRCRat Rig Community [Unofficial]

•Created by abitnutztoo on 8/25/2024 in #ratos-support

I see that BigTree has the new Octopus Max board out . Or maybe its not new and I just noticed it.

believe it is: https://os.ratrig.com/docs/boards/list/

3 replies

RRCRat Rig Community [Unofficial]

•Created by koekie40 on 8/21/2024 in #ratos-support

i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B

Just use a crossover (old school prob not necessary) or ethernet to a laptop

69 replies

RRCRat Rig Community [Unofficial]

•Created by koekie40 on 8/21/2024 in #ratos-support

i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B

yeah good call - keep it simple

69 replies

RRCRat Rig Community [Unofficial]

•Created by koekie40 on 8/21/2024 in #ratos-support

i'm trying to install RatOS v2.1.0.rc2 on Pi 4 B

Not an expert (haven't seen this before) but Checking progress 1 disk I think is related to fsck / Linux's disk checker. I would try re-burning the image using a different tool. Some have said the Raspberry Pi tool works fine, others Balena Etcher but an older version, and I think there was one other tool recommended (not coming to me at the moment). Or try a different SD card.

69 replies

RRCRat Rig Community [Unofficial]

•Created by 🌊 Jamiroquai 🌊 on 8/13/2024 in #fix-my-printer

RatRig V-Core 500 'Blew Up'

if you're in the UK / 220V I believe you're pulling 1/2 amperage of us in the US (120V)

36 replies

RRCRat Rig Community [Unofficial]

•Created by 🌊 Jamiroquai 🌊 on 8/13/2024 in #fix-my-printer

RatRig V-Core 500 'Blew Up'

the IEC plug meaning the receptacle with a fuse?

36 replies

RRCRat Rig Community [Unofficial]