Tripslip
RRCRat Rig Community [Unofficial]
•Created by Tripslip on 1/1/2025 in #fix-my-printer
skipping A and B's
I'm just asking is all. I will try but I would have thought that switching to the 5160's and 2804's would have improved my accelerations, not lower them. thats all. I'm just looking to find what I may be missing, not be a pain. 😆 plus, the skips are happening anround an hour or so into the print. lol
7 replies
RRCRat Rig Community [Unofficial]
•Created by Tripslip on 1/1/2025 in #fix-my-printer
skipping A and B's
7 replies
RRCRat Rig Community [Unofficial]
•Created by Tripslip on 12/30/2024 in #ratos-support
A/B steppers skipping.
this worked. Thank you
21 replies
RRCRat Rig Community [Unofficial]
•Created by Tripslip on 12/30/2024 in #ratos-support
A/B steppers skipping.
Right on. I was hoping to not have to re-rout wires and buy new steppers but I am trying to make this machine fast and reliable until I build a VC4 IDEX
21 replies
RRCRat Rig Community [Unofficial]
•Created by Tripslip on 12/30/2024 in #ratos-support
A/B steppers skipping.
is there another motor I should pick?
21 replies
RRCRat Rig Community [Unofficial]
•Created by Tripslip on 12/30/2024 in #ratos-support
A/B steppers skipping.
Roger that!
21 replies
RRCRat Rig Community [Unofficial]
•Created by Tripslip on 12/30/2024 in #ratos-support
A/B steppers skipping.
Have not done performance yet. still trying to get the machine working for the first time
21 replies
RRCRat Rig Community [Unofficial]
•Created by Tripslip on 12/30/2024 in #ratos-support
A/B steppers skipping.
which seem low for the motors and stepper drivers
21 replies
RRCRat Rig Community [Unofficial]
•Created by Tripslip on 12/30/2024 in #ratos-support
A/B steppers skipping.
21 replies
RRCRat Rig Community [Unofficial]
•Created by Tripslip on 12/30/2024 in #ratos-support
A/B steppers skipping.
RatOS is new to me, which config has the accels?
21 replies
RRCRat Rig Community [Unofficial]
•Created by Tripslip on 12/29/2024 in #fix-my-printer
! Hotend fan on when should be off !
I did. thats were I was making my errors. Im setting up RatOS for the first time and learning all od my unknown, unknowns
10 replies
RRCRat Rig Community [Unofficial]
•Created by Tripslip on 12/29/2024 in #fix-my-printer
! Hotend fan on when should be off !
10 replies
RRCRat Rig Community [Unofficial]
•Created by thanksihateit on 12/23/2024 in #ratos-support
Octopus V1.1 detected but is unresponsive.
This fixed it. TY
18 replies
RRCRat Rig Community [Unofficial]
•Created by thanksihateit on 12/23/2024 in #ratos-support
Octopus V1.1 detected but is unresponsive.
Thanks milkschmidt. I did but I as soon as updated from the mainsail ui it broke it. I only updated because Im trying to get my Orbitool board to work on a Voron template. Going to try a fresh install again.
18 replies
RRCRat Rig Community [Unofficial]
•Created by thanksihateit on 12/23/2024 in #ratos-support
Octopus V1.1 detected but is unresponsive.
I can not get past this either.
18 replies