toml
RRCRat Rig Community [Unofficial]
•Created by toml on 2/14/2025 in #fix-my-printer
'Extremely twisted gantry'
But I wouldn’t class it as fixed - I now have too much variance in probing for the beacon calibration to complete.
I just think the bed is probably not at issue for the twist now?
12 replies
RRCRat Rig Community [Unofficial]
•Created by toml on 2/14/2025 in #fix-my-printer
'Extremely twisted gantry'
Just what the video says.
I have actually used the video before, but I probably did about 40 runs/tweaks this time.
It’s kind of hard, need some jack screws really. I remember I was going to design some at one point. Little screw lifts that allow you to make micro adjustments between runs and can then be removed permanently. Maybe one day…
12 replies
RRCRat Rig Community [Unofficial]
•Created by toml on 2/14/2025 in #fix-my-printer
'Extremely twisted gantry'
Thanks for the help again! 🙂
12 replies
RRCRat Rig Community [Unofficial]
•Created by toml on 2/14/2025 in #fix-my-printer
'Extremely twisted gantry'
12 replies
RRCRat Rig Community [Unofficial]
•Created by toml on 2/14/2025 in #fix-my-printer
'Extremely twisted gantry'
Do you think the variance warrants it? 0.18mm over 400mm feels pretty reasonable to me given it's only at the absolute extremity.
Wondering if I'll be able to improve it as all three contact points (z-tilt) are similar, which leads me to think the bed is potentially just slightly not flat.
12 replies
RRCRat Rig Community [Unofficial]
•Created by toml on 2/12/2025 in #fix-my-printer
2.1 RC3 configurator can't flash board(s)
Thanks for the support guys! Really appreciate it. ❤️
19 replies
RRCRat Rig Community [Unofficial]
•Created by toml on 2/12/2025 in #fix-my-printer
2.1 RC3 configurator can't flash board(s)
19 replies
RRCRat Rig Community [Unofficial]
•Created by toml on 2/12/2025 in #fix-my-printer
2.1 RC3 configurator can't flash board(s)
Standard user, just with
passwd changed (via cli)19 replies
RRCRat Rig Community [Unofficial]
•Created by toml on 2/12/2025 in #fix-my-printer
2.1 RC3 configurator can't flash board(s)
Getting a perms error, it seems:
{"level":50,"time":1739393944902,"pid":4522,"hostname":"RatOS","err":{"type":"TRPCError","message":"Could not compile firmware for Octopus Pro H723 V1.1: \n\n Could not compile firmware for Octopus Pro H723 V1.1: EACCES: permission denied, copyfile '/home/pi/ratos-configurator/configuration/boards/btt-octopus-pro-h723-11/firmware.config' -> '/home/pi/klipper/.config'
Probably because I tried a manual clipper flash, shall delete the .config?19 replies
RRCRat Rig Community [Unofficial]
•Created by toml on 2/12/2025 in #fix-my-printer
2.1 RC3 configurator can't flash board(s)
Yea, it's a completely fresh board, straight out of the box from BTT.
19 replies
RRCRat Rig Community [Unofficial]
•Created by toml on 2/12/2025 in #fix-my-printer
2.1 RC3 configurator can't flash board(s)
STMicroelectronics_MARLIN_STM32H723ZX_CDC_in_FS_Mode_303F345D3231-if00
Is this not the H723's STM32 MCU?19 replies
RRCRat Rig Community [Unofficial]
•Created by toml on 2/12/2025 in #fix-my-printer
2.1 RC3 configurator can't flash board(s)
19 replies
RRCRat Rig Community [Unofficial]
•Created by fluffy on 5/31/2023 in #fix-my-printer
Leadscrews ratrig 3.1 kit 500³
As blacksmith says, I doubt with Oldham couplers it will make any difference. Bends don’t look too bad in the video, but maybe they’re worse in person.
6 replies
RRCRat Rig Community [Unofficial]
•Created by like-gold on 5/30/2023 in #fix-my-mesh
500 Bed Mesh kinda whack
Have you tried the methods in video found in FAQ?
https://discord.com/channels/582187371529764864/1047104248682385468/1047105404850667600
3 replies
RRCRat Rig Community [Unofficial]
•Created by subsequent-cyan on 5/24/2023 in #ratos-support
Webcam not found after Update to Crowsnest v4
Good news.
44 replies
RRCRat Rig Community [Unofficial]
•Created by adverse-sapphire on 5/24/2023 in #ratos-support
Webcam not found after Update to Crowsnest v4
That’s probably easiest yeah. Second hand Logitech c270 off eBay works well too I think if you prefer to wait until raspberry cam support is fixed.
I got one off eBay for just £5 and there’s a printable modification to adjust focus point.
44 replies
RRCRat Rig Community [Unofficial]
•Created by generous-apricot on 5/24/2023 in #ratos-support
Webcam not found after Update to Crowsnest v4
I'd recommend trying to use the
legacy/v3 option for now. If that doesn't work, I'd create a support thread over in https://discord.com/channels/758059413700345988/1036329187771957269 as the developers of Crowsnest will be able to help you better.44 replies
RRCRat Rig Community [Unofficial]
•Created by plain-purple on 5/24/2023 in #ratos-support
Webcam not found after Update to Crowsnest v4
For now you can switch back to
legacy/v3 by following the blog post to uninstall. Before you reinstall, switch the git branch:
git checkout legacy/v3
sudo make install
And you should be able to use your old configuration for now.
If you have raspberry camera v3, there is a project going on to add support this using another package.
https://discord.com/channels/758059413700345988/106427077011467067344 replies
RRCRat Rig Community [Unofficial]
•Created by quickest-silver on 5/24/2023 in #ratos-support
Webcam not found after Update to Crowsnest v4
Can you confirm which version of Raspberry camera you have?
44 replies
RRCRat Rig Community [Unofficial]
•Created by NMGMarques on 5/23/2023 in #ratos-support
Timelapse failing
Can you post your layer change gcode and moonraker.conf
8 replies