azoroes Comments - Answer Overflow

azoroes

Posts Comments

RRCRat Rig Community [Unofficial]

•Created by tg73 on 10/8/2024 in #fix-my-print

Regular surface distortion pattern towards end of larger first layers VC4

1754 replies

RRCRat Rig Community [Unofficial]

•Created by tg73 on 10/8/2024 in #fix-my-print

Regular surface distortion pattern towards end of larger first layers VC4

OK, I'll just install it completely from scratch so I can be sure it's not some faulty old software. All updates from today (including rc3/v8) 400mm square, 0,4mm height 265/110°c, 15-20 min heat soak, 0% fan Enclosure opened, print was with abs Start was really good but after some time it turned so bad I stopped, hope you can spot it on the picture Hope this helps

1754 replies

RRCRat Rig Community [Unofficial]

•Created by azoroes on 10/10/2024 in #fix-my-printer

Printer going totally wrong while Z-Tilt

Okay, went on it again and updated ratos as also os-packages, after this and a restart from my side the printer acted normal, only thing I had to change was the direction of the extruder but shouldn't have caused the problems. I'll keep you up to date if he is printing normal again or if something is happening

14 replies

RRCRat Rig Community [Unofficial]

•Created by azoroes on 10/10/2024 in #fix-my-printer

Printer going totally wrong while Z-Tilt

I'm pretty sure that's okay as homing works 100%, so x goes to the left till the sensor gets activated, then it's going back into middle position, same with y, going backwards till it hits the endstop and then going back into the middle of the bed. Z rises till it's sensed by the beacon and then goes back so it's about one cm from the nozzle. But as soon as I try z-tilt (where it should go front left, middle back front right) it does what you can see in the video

14 replies

RRCRat Rig Community [Unofficial]

•Created by tg73 on 10/8/2024 in #fix-my-print

Regular surface distortion pattern towards end of larger first layers VC4

Not a 100% sure what I used back then as I'm always trying to keep it as up to date as possible but I think it was ratos 2.1 rc1 Maybe I got time to try it later again

1754 replies

RRCRat Rig Community [Unofficial]

•Created by tg73 on 10/8/2024 in #fix-my-print

Regular surface distortion pattern towards end of larger first layers VC4

1754 replies

RRCRat Rig Community [Unofficial]

•Created by tg73 on 10/8/2024 in #fix-my-print

Regular surface distortion pattern towards end of larger first layers VC4

1754 replies

RRCRat Rig Community [Unofficial]

•Created by azoroes on 2/28/2024 in #fix-my-print

Severe first layer problems

I'll Try resetting my slicer with a new profile, I already thought if the brim is printed another height but I'm not sure how this could be changed (at least in orca) First layer is standard 50mm/s The spot on the printbed is badly always there but by taping one section I was able to get the total of nearly 0,9mm down to 0,4 over the whole 500*500 bed

6 replies

RRCRat Rig Community [Unofficial]

•Created by azoroes on 11/23/2023 in #fix-my-printer

4028 Fan not working correctly

Pa8 is the output according to the pinout sheet of the BTT Octopus v1.1

8 replies

RRCRat Rig Community [Unofficial]

•Created by azoroes on 11/23/2023 in #fix-my-printer

4028 Fan not working correctly

So the white cable is connected to the blue one on the delta 4028 fan, black is black and red is red

8 replies

RRCRat Rig Community [Unofficial]